Alien Gear Cloak Dock

Finally, an easy and smart way to mount a holster under the dashboard of your vehicle!

The product development folks at Alien Gear Holsters have another interesting product that interacts with the Cloak Mod OWB Holster (previous reviewed here). The Cloak Dock is a holster mount that allows you to attach your handgun holstered in the Cloak Mod OWB to whatever surface you desire. The biggest advantage I see with the Cloak Dock is you could conceal it at home or your workplace (if permitted) and have a car holster for the commute in between.

Thats right, you can mount your holster to the wall, under the desk, beside the nightstand, to the vehicle console, inside the safe door, or even in the shower! This lets you leave the gun in the Cloak Mod holster when its not being carried for convenient concealed access, yet detach and take the holster and gun with your on the go. AG generously saves you a trip to the hardware store by including an bunch of different screws and even a drill bit so you can mount the Dock onto a plastic, wood, drywall or sheet metal.

The template makes it super easy to mount the dock wherever you want, and the screws, anchors and drill bit included mean no trips to the hardware store.

Once you've picked where you want to mount the dock, use the template guide to drill the 4 pilot holes using the supplied 1/8" drill bit. AG recommends using a 1/2" bit for drywall installation (not included) due to the drywall anchors. If you are mounting into sheet metal, You can skip drilling pilot holes since the sheet metal screws are self-driving. Once you've mounted the two mounting brackets correctly, you have to decide whether you want the gun handle facing in or out, which is dictated by whether the alien head shaped paddle or the holster shell itself is facing outward.

Made your choice? Then you mount the docking bar between the two brackets with the correct label facing out (paddle side OR shell side) and the point of the triangular shape pointing down. Don't worry, the paddle will only snap over the docking bar one way, so its hard to screw it up. It's whether you have the bar reversed or not between the brackets that makes the difference. Depth adjustment is another design consideration that was implemented into the Cloak Dock, allowing you to tuck your gun closer up against the mounting surface, or protrude out farther for better access. Oh, and if you are wondering if your holster's cant will affect how it docks, don't worry... the dock has enough room for both forward and reverse cant, with one small limitation - at it's shallowest depth setting with the docking bar shell side out, the dock won't release a canted holster.

The docking bar's depth can be adjusted for less or more space between the gun and the wall.

Using the docking system is simple enough, just slide the paddle attachment of the Cloak Mod holster onto the center docking bar until the belt ledge of the paddle snaps over the bar. It should be as easy as a single fluid motion, with the added mass of the gun in the holster. The lockup is okay... not completely rock solid though. When its time to head out and you need to take the holster with you, just pull up from behind the paddle and pull the holster off the mount. It is possible to torque the gun's grip causing the the paddle to bend outward and freeing the locking ledge from the docking bar without having the manipulate the paddle yourself, but you would never do this unintentionally when drawing the gun from the holster. The draw is easy and clean, no different then if you had the holster on your belt.

In my small Toyota pickup, the best place to mount the dock is right under the steering wheel between my legs. Its out of sight incase I have to leave the Cloak Mod and my gun in the vehicle.

This is a great addition for gun owners wanting a solution for concealing inside of their vehicle, whether mounted under the steering column, alongside or even inside the center console. You could also purchase additional docks to place in the office or at home, even inside your gun safe's door for easy storage keeping the gun and holster together. When its time to head out and you need to take the holster with you, just pull up from behind the paddle and pull the holster off the mount.

FIREARMS INSIDER REVIEWS – 8 KEY POINTS

Claim to Fame: Attach your Cloak Mod OWB Holster to a variety of surfaces with the all-new Cloak Dock Holster Mount.

Target Market:  Cloak Mod OWB owners wanting to "dock" their firearm in a vehicle, office, etc.

FNBs (Features & Benefits of this product):

  • Interfaces with Cloak Mod Holster
  • Constructed of glass filled nylon
  • Mounts to plastic, wood, drywall or sheet metal
  • Docking Bar configurable for left or right hand orientation
  • Accommodates both forward and reverse cant of Cloak Mod Holster
  • Comes with template for drilling holes
  • 30-Day Test Drive and Forever Warranty. 

What other aesthetic options or finishes are available?:  Black only

WHAT OTHERS ARE SAYING?: 

"I been wanting something like this for a while and I am glad alien gear came out with this. I had recently purchased the OWB holster but I never really used it since I conceal carry, and for only 15 bucks I was able to convert it into a bedside holster. Now I can quickly grab my gun in an emergency which is only 20 inches form me now mounted on the side of a book shelf. Alien gear is amazing, I order it only 3 days ago and it arrived already. They keep coming up with awesome products and continue to sell them at ridiculously low prices" - Website Review

"This is a need to own product. (must own cloak mod 3.0 holster) I just received the cloak dock in the mail, I was extremely excited to get it installed but Where?? Well being In Arizona and having a ccw permit, I decided to set it up in my 2014 Nissan Frontier. With very little room to the center consle it wasn't difficult to install,. I still have enough leg room and it's at the ready. With it's versatility you can mount to plastic, wood or thin metal. Also you can switch the sides if you want the paddle or shell facing out, Highly recommend this product" - Website Review

PRICE POINT:

I NEED IT NOW! AVAILABILITY:

Alien Gear Holsters

OUR RATING:

Pros:

  • Adaptable in either padded in/out configuration for left/right handed.
  • Easy to remove holster to switch to carry
  • Includes 1/8 drill bit, nice!

Cons:

  • If your holster paddle is setup for a cant, it won't release when shell side out if the dock is set to the its shallowest depth
  • The locking interface could be more secure

SCORE: 7.0 GOOD

 

Featured FFL:

For FFL services I choose Promised Land Firearms in Toulon, IL.

Ryan's Links:

Gun & Gear Review Podcast
Hunter of Design

Sig P938 Scorpion

I've recently made the switch from carrying a full size double stack 9mm to a single stack pocket gun on a daily basis.

I've been wanting to review this little pocket pistol for quite a while now. It's quickly becoming my favorite CCW gun, perhaps even my favorite in the entire collection. Not only is it a nearly perfect carry, but it shoots really, really well.

I quite enjoyed my time shopping around for a dedicated EDC handgun that could easily and discretely fit in the pocket of my pants, jacket or vest. Ultimately I was searching for something that would become my summer carry, and backup carry in the fall/winter. My standards were pretty simple: 9mm single stack, 7+1 capacity of higher, 3 inch barrel, tritium sights or aftermarket availability of night sights, manual safety, and above all else it had to fit in a pocket holster like a DeSantis Nemesis or Sticky Holster.

In the DeSantis Nemesis holster, the P938 practically melts into your pocket. Any minor imprinting would be taken as a wallet or bulky smart phone instead of a gun, even with the extended magazine.

Fortunately at the time I had the luxury of working at one of the largest gun shops in the country, and everyday I got to handle all the potential candidates as well show customers who were shopping with the same parameters as I had in mind. The top 5 guns in the running were the Glock 43, S&W M&P Shield, Ruger LC9s, Springfield XDs and Sig P938. Obviously from the title and photos of this review, I picked the Sig. What did it for me was the overall length of the P938 was among the shortest, not an iota of polymer, tritium iron sights right out of the box, and it carried the reputation of a Sig firearm... high price, high quality. You really get what you pay for with this little guy, and you are actually getting a lot.

This is the baby 1911 for the 21st century, with everything I need and nothing I don't. Okay the laser wasn't a necessity, but on a short barrel gun its a nice addition.

The pricetag of the P938, or any Sig for that matter, often turns shoppers off and draws them toward the cheaper polymer frame pistols that are a good three to four hundred dollars cheaper. For a short while I was on the fence too. However after feeling the P938 in my hands 5 days out of the work week, a bond was formed and a fanboy was born! There are so many colors and aesthetic options for the P938, just like its older brother the P238 in 380acp. My heart was set on either the Extreme with its grey G10 grips, or the Scorpion with its Flat Dark Earth Cerakote and rattlesnake-like Hogue G-10 grips.

I chose the Scorpion because I wanted something different than a black gun, and Cerakote is a fantastic finish for longevity and wear. It does carry an extra $80 to the price at some retailers, but the heart wants what the heart wants. The P938 comes with a hard case, lined with cut foam to secure the pistol, extra magazine, minimalist holster, and a laser if desired. The magazines that came with my Scorpion is the 6 round flush bottom mag, and the 7 round mag with a finger extension. I believe some P938 models only come with the 6 round mags but the 7 rounder extended mags are sold seperately for about $40-50. The holster SIG included is a nice afterthought, but just like with an XD with gear from Springfield I usually just leave it in the box and use something else higher quality.

At first the ~$7-800 price tag was daunting to me, but the inclusion of SIG LITE night sights from the factory and the cerakote job made it easier to justify.

The beauty of the P938 in my eyes is that its basically a mini 1911. If you are familiar with the iconic Browning design, you'll be used to the magazine release button, slide stop, and thumb safety as well as using a single action with a mainspring housing and external hammer. It does not have a beavertail grip safety or a barrel bushing (thank God) and it actually has an ambidextrous safety thats not too obtrusive. There's a big chunk of the CCW community that believes a carry gun must be cocked and locked with no external safeties to fumble with... and I won't entirely disagree. In this case though of a single action, the safety should be engaged when carrying with a round in the chamber. When engaged, the safety blocks the hammer from moving. It may take awhile for someone to grow confident with this mode of carry, but I've found it to work just find.

You could carry with nothing in the chamber and hammer down, or hammer up to ease racking the slide, but honestly its a waste of time and overly cautious. Drawing a loaded single action and disengaging the safety can be a fluid and safe motion, if you practice and use common sense. 

Disassembly of the P938 is basically simplified version of taking apart a 1911 with a few less steps. Drop the mag and check for clear chamber, safety off, and pull the slide back while pressing on the slide release from the right side, just enough where you can pull it out from the left side. The slide should slide forward with ease now and separate from the lower. Now just pull out the recoil spring CAREFULLY because that will fly across the room if your aren't careful. Do it inside a bag if you need to. Then pull the barrel out and you are all set to clean, lube, and reverse the steps to reassemble. There is a thin metal hinged hook that is fragile near the hammer mechanism protruding from the frame, and when reattaching the upper slide you need to guide that hook down under the slide so it doesn't get bent. Push the slide release pin through the slide and pseudo barrel linkage while pulling that slide back until in snaps into place, and its ready to rock and roll.

The P938, just like other duty/combat SIG pistols, are set up to use a "combat" sight picture (front sight completely covers bullseye).

This group was shot aiming at the top of the diamond outline @ 15 yards using 115 grain FMJ ammo.

Now for my favorite part of a gun review, shooting the darn thing! The P938 looks like it would be a snappy pea shooter in 9mm due to its size, but I find it pleasant and smooth. I shoot my fair share of larger calibers, but 80% of the time I'm shooting 9mm so my hands aren't desensitized to recoil. The recoil spring and slide makes for a smooth and controllable impulse, and reacquisition of the sights is quick. The sight picture is very similar to shooting a 1911, and there is a potential for nice groups. Obviously this is no target or bench pistol, and if you plan on carrying it everyday like I do, then you need to train for shooting more active and stressful drills. Bad guys don't hold still, and they shoot back.

One of the first things I noticed when putting the initial rounds downrange with the P938 is that with a smaller framed single stack pistol, you have to pay attention to how much finger you use. Its easy to overinsert your finger into the trigger guard and use the first crease of your booger-hook to do the trigger pulling, which will cause your shots to fly left of the point of aim (right if you're are a lefty, hypothetically). Consciously using the pad of my finger instead brought the groups right into center of my point of aim.

This lil devil of a pistol will be my reigning EDC for years to come because it conceals well, and shoots very well for its size.

In my eyes the P938 is the finest pocket pistol in its class. By no means will I hate on the Glock 43 or M&P Shield because those are great little guns too. I love striker fired tupperware guns just as much as the next guy. However for me, depending on a quality pistol like the P938 on an everyday basis is a nice reassurance to have in the make of my mind.

FIREARMS INSIDER REVIEWS – 8 KEY POINTS

Claim to Fame: With the introduction of the P938, SIG SAUER now offers the ballistic advantage of the 9mm cartridge in a platform similar in size to the best-selling P238 pistol.

Target Market:  Concealed Carry / Home Defense

FNBs (Features & Benefits of this product):

  • Caliber: 9×19 (there is a .22 LR variant as well as two 9mm-to-.22 LR conversion kits)
  • Capacity: 6+1 or 7+1 with extended magazine
  • Barrel Length: 3.0″ (threaded barrel variant also available)
  • Overall Length: 5.9″
  • Height: 3.9″
  • Width: 1.1″
  • Weight: 16 oz with unloaded magazine
  • SIGLITE Night Sights
  • Grips: Hogue Overmold, Rosewood, G10 (varies by P938 sub-model)
  • Trigger: Single Action Only. 7.5-8.5 lbs pull weight (7 lbs as tested)
  • Includes a Holster

What other aesthetic options or finishes are available?:  Plenty!

WHAT OTHERS ARE SAYING?: 

"Overall, the SIG Sauer P938 is more pleasant to shoot than you’d likely expect. I’m sure it would be even better with an extended mag that allows all five fingers to join in on the fun. It’s super light, feels like a “real gun,” runs reliably, and is one of the easiest-to-conceal 9mms available. The cost of entry is on the high side, but the quality is commensurate. Where I really think the P938 is worth it is when you’re used to shooting a hammer-fired pistol with manual safety — especially and particularly a 1911. If you compete with a 1911, target shoot with one, carry one when your attire affords it, etc etc, then the P938 is a no-brainer. Same manual of arms in a carry piece or backup gun as your primary or as what you’re most used to and trained on? Yes, please." Truth About Guns Review

"The gun fits my hand great for a compact. I am pretty tall and have long fingers. The grip on this gun is a little wider than other compacts, so it's easier for me to feel comfortable with my grip. Also, with the extended mag that comes with the pistol, I don't have that awkward hanging pinkie. The handle is more square than say, a Glock, which has an oval shaped handle, so for me it is easier to keep a good grip, especially in hot weather. This comes standard with Sig Sights, which are "night glow" raised sights. I have poor vision, but have no difficulty aligning the sights in my dark hallway with no contact lenses in.The sight corners are rounded to prevent it from snagging on clothing during draw. As with all Sigs, the slide is really easy to rack back, it almost feels like it's on a ball bearing track compared to other pistols I own. From this compact 9 mm to my .45 1911, I have NO trouble racking Sig Sauer pistols and I don't feel fatigued from racking them when shooting for long periods of time. The "off the shelf" trigger weight is pretty lights (I can't recall the weight offhand), but it is lighter than that of other pistols I have. I like a light trigger, so I was pleased that I didn't have to adjust or upgrade this one. This pistol has very little recoil; I suppose because the pistol itself is a bit heavier than other models its size. I do like the weight, I feel it helps me recover to target better after a shot. Keep in mind though, grip and stance play a huge part in managing recoil." - The Well Armed Woman

PRICE POINT:

  • MSRP: $893.00
  • Retail: $630-$800

I NEED IT NOW! AVAILABILITY:

Check your local SIG Dealer.

OUR RATING:

Pros:

  • Recoil is pleasant for a small frame/barrel
  • Night Sights right out of the box
  • Ambidextrous Thumb Safeties
  • Chamber can be cleared with safety still engaged
  • Cerakote makes cleaning easy, looks great
  • Easy Takedown

Cons:

  • Non Ambidextrous Mag Release
  • Beavertail in frame is small and doesn't protect large fatty hands
  • Gap in slide ejection port on right side

SCORE: 9.0 AMAZING

 

Featured FFL:

For FFL services I choose Promised Land Firearms in Toulon, IL.

Ryan's Links:

Gun & Gear Review Podcast
Hunter of Design

2 Likes

 

SOG TOC 20 Backpack

  Most people have heard of SOG knives. Well, SOG has now gotten into the backpack market. They are offering a pretty good selection of different size and use packs. They sent me one of their smaller ones, the TOC 20 in gray. The "TOC" stands for Tactical Operating Center. Thanks to SOG's website I now know this. When the pack first got here, there was very little info in the web about it, now SOG has plenty of info on their packs.

  I have lugged this TOC 20 pack for about 3 months now. It went to a couple trade shows with me. I used it as a makeshift range bag on a few occasions. But I didn't drag it behind a truck. The pack is very useful. Not the largest, it is stated as a 20 liter pack, but a nice size for day hikes, concerts, trade shows, or just lugging around town. The padded straps are a nice touch, once the pack is loaded with stuff. The straps are also quickly adjustable with pull straps at the bottom. There is also an adjustable strap that goes between the two shoulder straps, that latches them together at about chest level. I am sure there is a name for it, but I can't think of it. These straps will also slide up or down on a little rail system for best comfort and fit. The little buckle also has a built in whistle. Also on the straps are various Molle straps and some eye loops.

Looking Inside Main Compartment

Looking Inside Protective Pocket

  Now on to the pack itself.  The TOC 20 has 2 main compartments and 3 smaller ones. The main compartment, as I will call it, opens up at the top with the zippers going about a third of the way down the sides. Once open, one has access to the full depth and width of the pack. Inside the main compartment are 2 other zippered pockets, one on the front and one on the back. The front zippered pocket zips in the center and has a little lanyard loop inside. Probably for your keys. The other one zips all the way across and is about 5" deep. Along with the inside zippered pockets, there is also one that is just open. But on the front of this pocket are little inserts to slide pens, knives, etc into. Now behind the main compartment is another full size one. This one is for either a laptop or a water bladder. This compartment is what they call a pass through. It has full length zippers, one on each side of the pack. On the front of the pack are two zippered pockets, one on each side. These pockets are really nice to store bottled water, etc. I carry medical stuff in one of them. At the top of the pack, on the front, is a hardish padded dome pocket. This pocket is used to protect something like a cell phone or sunglasses, etc. Also, inside the padded pocket are some other little pockets to store stuff in. The only real problem I ran into with this protective pocket, was that it is easy to accidentally open it when trying to open the main compartment. Then everything in it falls out, defeating the protectiveness of the pocket. On the outside of this "safety compartment" is some hook and loop to put your Patriot Patch Co, patches on. All the pouches/compartments have dual zippers with finger pulls. The pulls are actually pretty sharp at the bottom of the half circle, but are big enough to work well without any problems. 

  Now on the front of the pack, they put this pannel with slots in it. This panel makes it possible to attach Molle gear and other such items. It is made from Hypalon. Hypalon is a durable synthetic rubber used on inflatable boats and such. I pulled pretty hard on these slots. It didn't even stretch them. It also has some other cloth Molle attachment points on the pack bottom. 

  Now that we have covered just about everything. The TOC 20's outer shell is made from 500D nylon. They also coat the nylon with polyurethane to give it a water resistant coating. I never dipped it in water, but the coating should help when it's raining. There are also two carry handles, one on the top, and one on the side. So if you don't want to sling your pack, there is another option. 

  So if you're looking for a new pack, look into SOG. Not your normal pack maker, but the TOC 20 is a good pack. And if you want something larger, they make those too. 

Firearms Insider Reviews - 8 Key Points

Claim to Fame:

Tactical Day Pack

Target Market:

Day hikers, students, or anyone looking for a small well organized daily carry pack

FNBs (Features & Benefits of this product): 

  • 20 liter capacity
  • Padded shoulder straps
  • Adjustable sternum strap w/whistle  
  • Molle attachment points
  • Impact resistant top storage compartment 
  • Pass through access to laptop/hydration area
  • Plenty of pockets and compartments
  • Large zipper pulls
  • Water resistant  
  • 20.1" x 11" x 7.5"
  • 32.5 ounces 

What other aesthetic options or finishes are available?

Black

What others are saying?:

Scratch at sogknives.com 5 /5 stars.

Thoughtfully designed and real good quality

I've long been a fan of SOG products so I had high expectations for the TOC 20. I wasn't disappointed. The quality of materials and construction is high and attention was paid to smaller details like zipper pulls and straps. The bag has multiple compartments allowing for separation of wet/dry and hard/soft gear, all of which are easily accessible. The ability to access the main areas through side zips, and the side handle are especially useful when traveling. The impact resistant top pocket is cool because when you open it, it acts as a tray - something I've liked on various fishing gear I've owned - which gives you good access to the contents without the risk of your stuff falling out. Finally, comfort - I'm over 6 feet tall and 250 lbs. with broad shoulders. Most day packs have straps that are either too narrow, too short or badly angled. The straps on my TOC 20 fit comfortably, even when the bag is fully loaded. It also feels good against my back while hiking or even jogging. If you're looking for a well-made, versatile day pack with with quality construction and features, the TOC 20 is a solid choice.

Link to other reviews:

None Found

Price point:

(MSRP versus actual retail)

MSRP = $159.99 at sogknives.co

Retail = $113.86 at Amazon 

I need it now! Availability:

Amazon or SOG knives 

Our Rating:

Pros:

  • Padded straps
  • Adjustable sternum strap
  • Molle attachment points
  • Water resistant  
  • Side and top carry handles
  • Pass through compartment  
  • Hydration compatible  
  • Protective compartment

Cons:

  • Zipper pulls are sharp
  • Easy to accidentally open protective compartment when trying to open main one
  • Big SOG logo
  • Too tactical looking

Score: 7.5 Good

 

Chad's favorite link: Axelson Tactical
 

Wisconsin Trigger Company M-K IIA2 Trigger

Some people spend a lot of hard earned money on aftermarket gun parts to squeeze more accuracy out of their AR-15 rifle. Pricey barrels, tricked out stocks, fancy receivers and other mods can play a crucial role in ergonomics, harmonics and other factors that affect the bullet traveling down the bore, but they aren't nearly as important as the trigger mechanism. Anyone worth their salt in the shooting realm will tell you the trigger can make the difference between a good group and a bunch of excuses. The finest barrel on the market won't do much good if a laborious trigger pull causes drastic variation before the shot breaks and the bullets leaves the muzzle. Any deviation, even by a degree or two, can throw the shot off target.

The AR-15 trigger has seen a huge jump in design and engineering advancement in the last 57 years. Most shooters would have a hard time holding consistent 1 MOA groups at 100 yards and further using a gritty, stiff single stage trigger. Precision shooters require a crisp break that prevents the shooter from exerting any unnecessary forces on the rifle during the moments when the trigger is pulled, freeing the hammer to swing into the firing pin and detonate the primer. Even the microseconds when the powder is ignited and the projectile travels down the bore, excessive movement from trigger overtravel or continued pulling force can move the barrel off the point of aim.

Thankfully improvements in sear disconnects, spring weights, and user adjustability have turned the old Armalite rifle design into a strong contender on the range for competitive marksmanship. Competition shooters often select match grade two stage triggers for their precision builds.  A two stage trigger has a first stage "takeup" of average pull-weight that comes to a stop when pulling slowly. This wall allows the shooter to breathe, focus on the target and stage the second step, a hair more of pressure that releases the hammer. The overall force needed to fire is the same between a two stage and a single stage trigger of the same weight rating, but the two stage requires much less pressure in the final stages before the actual break

The Milazzo-Krieger Two Stage Match Trigger System, or M-K II is the first patented two stage match trigger system for the AR platform. If you're wondering where you've heard of it before, you may have spent some time at Camp Perry. The M-K II has been widely used in M-16 rifles competing and setting records in the US Army Marksmanship Unit (USAMU) since the early 1990's. Production stopped in the mid 1990's, however the Wisconsin Trigger Company began to offer the M-K II trigger on its 25th birthday using all the original tooling and fixtures. The first generation of M-K II triggers required some trimming of the metal at the back of the trigger unit to adjust overtravel, but luckily the Gen2 model resolved the need for unpleasant grinding.

Comparing the M-K IIA2 trigger (left) and the Rock River Arms two stage trigger (right) you can see the RRA disconnector is preset and not adjustable.

Left: M-K IIA2 trigger. Right: RRA trigger

The next generation of the M-K II, designated as the M-KIIA2 was designed with the tactical shooter in mind. The Wisconsin Trigger Company implemented a user-adjustable second stage release via an allen screw that moves the disconnector up and down. This allows the user to find the precise moment where rearward trigger movement contacts the disconnector and forces the second stage to break on their rifle, which is called the "Zero Point." They also incorporated a factory set over travel, forward trigger overtravel, and small pin and large pin Colt styles.

Left: M-K IIA2 hammer. Right: RRA Hammer

Installing a AR trigger thats not a singularly housed drop-in component can be intimidating if you haven't done it a few times, but the instructional booklet and the online videos on the manufacturers website help clarify the process. Basically you remove your existing trigger components, install the M-K IIA2 trigger first, then put the MK-11A2 hammer in. The M-K IIA2 has a redesigned disconnector (the wedge shape that forces the hammer to slip away from the trigger's sear) that moves up and down with a simple screw, and provides a faster hammer reset (AKA faster shooting).

You need to remove the safety selector to properly install the trigger, so just loosen the pistol grip enough to pop it out temporarily.

The supplied trigger and hammer pins were tight enough to warrant using a hammer and punch. I don't see them walking out anytime soon.

Tightening the screw all the way down moves the disconnector downward and out of the way, removing the second stage of the two stage trigger pull alltogether. Backing the screw back out will re-establish that second stage contact with the disconnector and increase the pressure needed to achieve that break. Following the instructions, you delicately and patiently keep adjusting the screw up and down while pulling the trigger/manually resetting the hammer until you find the precise moment of contact where a mouses breathe could set off the second stage. Then you must back out the screw by approximately 3/8 of a turn... this is the factory recommended setting for adequate safety. I myself felt that 5/16 turn was more preferable. Then all you do is back it out 4 full turns, apply a thread locking compound, and retighten 4 turns back to your personal setting.

Finding the "0" point is tedious, requiring minuscule increments of tightening/loosening until you barely first feel contact with the disconnector.

I used a paint pen to mark an indicator dot, which allows you to back the screw out precisely for the final position, and then in and out again for the Loctite application.

I used the tip of a small narrow phillips screwdriver to apply the blue Loctite to the disconnector adjustment screw... its a tight space so this was the easiest solution.

But that’s not all. The M-KIIA2 also comes with three varying weight disconnector springs. They are colored red, white and blue (the blue spring comes factory installed in the trigger) The white spring is the heaviest at 5.0lbs, whereas the blue is the middle ground at 4.5lbs and the red is the lightest at 3.25lbs. I opted to leave the blue spring as is, because I was satisfied with the break I had found with my adjustments of the disconnector.

The included chart and instructions make it easy to change out the disconnect spring for lighter of heavier personal preference.

The redesigned disconnector of the M-K IIA2 also provides a faster hammer reset over traditional trigger systems. The forward trigger over travel allows the trigger to move forward after the hammer has reach it's reset, keeping trigger spring pressure on the shooter's finger which greatly reduces "trigger slapping" when shooting high speed consecutive shots.  In a 3-Gun or other competitive setting where a carbine must be proficient in both close range/fast target transitions as well as long range, slower and precise shooting, this two stage trigger system really shines.

*Note: I will post range photos in a future update. The day before a planned range trip I injured myself pretty badly. Stay tuned for groups of both slow fire at 100 yards and rapid fire at 25 yards.

Overall I was very pleased at the performance of the M-K IIA2 trigger. Installation was no different than a standard trigger, but the ability to change out spring weights and tune the disconnector with ease are huge benefits to someone wanting a more personal touch to their AR-15 trigger. Since publishing this review, the M-K IIA3 trigger was released, that retains the features of the A2 with the addition of an ambidextrous safety selector with a hole which allows to user to fully adjust the trigger overtravel.

FIREARMS INSIDER REVIEWS – 8 KEY POINTS

Claim to Fame: The M-K IIA2 combines the original M-K II world class match trigger release with a high speed trigger design.

Target Market:  AR-15 owners: competition or recreation

FNBs (Features & Benefits of this product):

  • Adjustable second stage release
  • Factory set over travel
  • Forward trigger over travel
  • Available in small pin (GI Type) and Large pin Colt Styles
  • Short hammer reset
  • Redesigned disconnector
  • Quick installation and tuning
  • Includes 3 different weight disconnector springs: White 5.0lb, Blue 4.5lb, & Red 3.5lb
  • Includes Slip 2000 Lube
  • Instruction manuals & Spring Chart
  • Transferable Lifetime Guarantee

What other aesthetic options or finishes are available?:  Bronze bearing version available

WHAT OTHERS ARE SAYING?: 

"For those who are looking for an extremely crisp AR15 trigger that closely mirrors the “feel” of a finely tuned M1 / M14 trigger, this trigger might be the solution. The first stage is exceptionally clean and smooth due to a proprietary diamond-grinding process. I felt that the first stage travel was longer than a Geissele, but many guys will prefer that. Upon reaching the very noticeable and defined “wall” of the second stage, a further increase of pressure provides the instantaneous snap one looks for in a high-quality trigger — complete with a total absence of anything resembling creep or slop."
Johnny Fisher, accurateshooter.com

PRICE POINT:

  • MSRP: Starting at $225.00

I NEED IT NOW! AVAILABILITY:

Bravo Comany USA or check other Wisconsin Trigger Company dealers

OUR RATING:

Pros:

  • 3 different disconnector spring weights allow user to choose between light, standard or heavier pull weights.
  • Trigger and hammer pins were nice and tight (punch and hammer required)
  • Documentation/Instructions included are thorough (but videos were more helpful during the actual installation)
  • Stickers and magnet swag!

Cons:

  • Standard GI trigger blade shape
  • Other components of trigger assembly are off-limits (unsafe and void warranty if tampered with)
  • Thread locking compound not included

SCORE: 8.5 GREAT

 

Featured FFL:

For FFL services I choose Promised Land Firearms in Toulon, IL.

Ryan's Links:

Gun & Gear Review Podcast
Hunter of Design

Patriot Concealment Annihilation IWB Holster

Inside the Waistband holsters should be comfortable, secure, and simple

Kydex Inside the Waistband (IWB) holsters can be classified into three categories. Lavishly comfortable, feature-rich and expensive... simple and efficient.... and cheap junk. Luckily I don't do many reviews of the third kind of holster, and like many of us I am not wealthy enough to spoil my guns with exotic materials and fancy gadgetry. This time I wanted to review a solid, simple and relatively affordable kydex holster that is built to flat out work and work hard.

With a slim single stack pistol, the Annihilation really feels minimal behind the hip.

The Annihilation IWB Series holster from Patriot Concealment Solutions is a dedicated inside the waistband holster. Its a very simple design that bears a lot of resemblance to other kydex holsters on the market, until you see the quality and customization that it offered upon ordering your own holster. I was told is the Annihilation IWB holster was the most popular product among  Patriot Concealment's customers, and I had to give it a try for myself.

With a double stack frame, the thickness of the holster is going to be more noticeable.

The Annihilation boasts more than just a obviously awesome name. There are several options available to the customer in order to make the holster just right. Starting with your gun make/model and left or right handed orientation, you can then choose between three sweat shield lengths, three front sight channel sizes (to accomodate oversize or suppressor height iron sights), a nice selection of colors/patterns, IWB fold over clip or soft polymer snap loops, an optional concealment claw, and whether your handgun has a threaded barrel, accessory rails, or a slide mounted optic that needs to be accounted for in the kydex mold for proper fitment.

The Annihilation can also be used as AIWB (appendix inside the waistband) and can be easily adjusted for comfort in your sitting down.

The only options missing that you often see in other competitor's holsters is an adjustable cant angle, and the option for ambidextrous hardware for swapping orientation and which side of the hip you are carrying on. Patriot decided to make a permanent 15 degree forward cant, with the reasoning that in the most ideal carry position of near one's kidney and just above the user's wallet, the preset 15 degrees of forward cant provides the proper angle for reaching the grip and drawing the firearm. Personally I like the option to set me own cant angle, but the simplistic design of the Annihilation is really only comfortable in two positions on my belt, 4:30 -5:00 at the back of the kidney as suggested... or appendix carry (only if you selected the shorted sweat shield so your not jabbing yourself in the gut) however the inability for a negative 15 degree cant rules the latter position out.

The kydex covers the mag release to prevent any unintended mag drops

The hardware is solid and idiot-proof

The retention is user adjustable by the tightening or loosening of two phillips head screws compressing rubber bushings forward of the trigger guard. I believe this is a standard, must-have feature on any holster, unless it falls into that "Cheap Junk" category mentioned earlier. The Polymer FOMI clip is easy to use, overlapping the waistband of pants and accommodating belts up to 1.5 inch width and a generous thickness of 3/8 of an inch. The thickness of the belt clip is a double edged sword... while it gives the user an ability to move the holster on the fly to find their sweet spot... the lack of friction on belts 1/4 inch or thinner will likely cause the holster to move too freely, depending on your figure and tight your pants holds the holster against your body. Some manufactures address this by offering different sizes of belt clips. Of course you do have the option to substitute a polymer soft belt loop with a snap button, but I'm not a big fan of those either personally, and they add an extra $15 to the total cost.

When ordering a custom Annihilation, you can also select the size of the front sight channel in case you have a taller suppressor height front sight.

In all honesty, this holster design has never been the most comfortable or concealable for my body type, pants and EDC belt choice, but it has been known to work for plenty of other concealed carriers. I'm not afraid to say loosing 30-50lbs would make this design more comfortable on my belt, and also print less. However the most positive feature I can point out about this small and efficient use of kydex, is that you can fully wrap your hand around the pistol's grip without any hinderance from extra kydex, belt loops, or anything. This is really nice when practicing drills of drawing from concealment garments, as there's nothing to get in the way of a nice solid purchase on the grip.

The height of the sweat guard is also customizable. I really like the standard non-extended height so I don't get jabbed in the flab as much.

All-in-all, the Annihilation is an easy to use, no frills IWB holster that is rock solid in hardware and construction. With the ability to choose customizations for a tricked out pistol with aftermarket accessories without spending $80+ on a custom holster. The saying "Simpler is Better" or "Keep It Simple Stupid" definitely applies to the strength of the Annihilation holster.

Another great feature is the how flush the kydex is to the pistol's trigger guard, so there nothing getting in your way of a full and firm purchase when gripping the frame.

**NOTE: If you have a popular holster model and don't require as many customization options, Patriot Concealment offers a "Quick Ship" option to get the product in your hands faster (3-5 days vs the 4-6 typical lead time for a customized holster) Models included are Glock 42, Glock 43, Glock 26/27/33, Glock 19/23/32, Glock 17/22/31, S&W MP Shield, Springfield XD-S 3.3, and the Sig Sauer P238/P938. Color is Black Carbon Fiber only, right handed only, and sweat shield size is full.

FIREARMS INSIDER REVIEWS – 8 KEY POINTS

Claim to Fame: This holster has been battle tested and proven to be a go to choice for concealed carry.

Target Market:  Concealed Carry Handgun owners

FNBs (Features & Benefits of this product):

  • Light Weight
  • No Added Bulk, .080 thickness
  • Hardware is American Made Brass & Steel finished with Black Oxide
  • Adjustable Retention
  • Customized molded for each individual order
  • Each Order custom finished to perfection

What other aesthetic options or finishes are available?:  Black, Black Carbon Fiber, Storm Gray Carbon Fiber, OD Green Carbon Fiber, Killer Coyote Carbon Fiber, Coyote Brown

What others are saying?: 

"I regularly carry everything from a Glock 26 all the way up to an HK45 and have bought many holsters. I ordered one of these for my glock 26 having not found a viable everyday carry IWB holster that met all my needs. I was looking for something comfortable in every position (2-6 o'clock) and something easily concealable. This holster exceeded my needs. So comfortable I can't tell it's there, small in size, and the best holster on the IWB market for reholstering the gun! I have owned crossbreed, aliengear, Galco, desantis, and many more but I liked this holster so much I went ahead and ordered one for my Glock 23 and my Sig P320 which are my other 2 guns most widely used in my rotation. Excellent quality, excellent functionality, and excellent customer service. I am very picky on holsters so I would urge everyone to buy one of these, you will not be sorry!" Seth Wright, customer

"I am a big guy....you know the adage for big guys, I have enough inside the trousers why would I want to carry IWB, get an OWB.  With this holster this is not the case, it is extremely comfortable, I wear appendix carry and there is no problem with this holster while sitting, especially in a car. Excellent holster at an excellent price." Bear Miller, customer

PRICE POINT:

  • MSRP: Starting at $64.99, add-ons increase price

I NEED IT NOW! AVAILABILITY:

Patriot Concealment Solutions - Quick Ship available for popular gun models here

OUR RATING:

Pros:

  • Very lightweight
  • Design gives user 100% access to frame's grip

Cons:

  • Limited carry positions for comfort
  • Cant angle is preset
  • No beveled edge or flared mouth to assist in reholstering
  • No instruction or literature included

SCORE: 7.0 GOOD

70.jpg
 

Featured FFL:

For FFL services I choose Promised Land Firearms in Toulon, IL.

Ryan's Links:

Gun & Gear Review Podcast
Hunter of Design

LUCID L5 4-16x44 Scope

 A long, long time ago... Oh wait, wrong story. Now, on to the Lucid Optics L5 scope. I was looking for a scope to mount on my Savage, that now sports the MDT chassis. I sent Lucid a request because I had heard good things about them. They decided to send me the L5 in 4-16x44. They also sent me one of their L7's which will be reviewed later.

  Now it was time to mount the scope up. So, I went and purchased some 30mm rings. My local store was out of the Warne rings I wanted, so I opted for the Weaver Tactical rings. The scope dropped nicely into the medium height rings without any problems. Once leveled, clamped down, and bore sighted, I took it to the range to see how I liked it. After sighting it in, I was ready to get some time behind it.

  Lucid touts the 4-16 as their "Cross Over" rifle scope. I would have to agree. In this optic range it will be well suited for hunting and also work well at the range. Now onto the important stuff. The L5 uses a one piece 30mm tube for its main body. By having a 1 piece tube, the L5 should be fairly rugged. It uses a 34mm ocular lens (the one you look through) and a 44mm objective lens. The "L5" reticle is glass etched on the second focal plane, and for the price I wouldn't expect it to be a first focal plane. Weighing in at 18 ounces, it is comparable to other scopes of this size. It uses a side focus parallax adjustment that is adjustable from 15 yards to infinity. The eye relief is fairly generous at 3.25"-4.25". Click adjustable turrets give you 50 MOA of windage and elevation adjustment. 7.5 MOA per revolution in 1/8 MOA clicks. The L5 also has all of the usual scope stuff: fog proof, water proof, etc.

  While using the L5, I started to really get an appreciation for the reticle. The L5 reticle has fine enough marks that I could make very precise shots. The center aiming point is a small 0.125 MOA dot. When using the BDC, the lines are also not too thick. The BDC lines are spaced every 2 MOA down the reticle and are 1 MOA wide. At first I thought "why not every 1 MOA", but after using the reticle, I actually started liking it. Mainly because it wasn't too busy and filled with lines. There are also windage dots spaced 4 MOA across the reticle. Depending on your ballistics, these may or may not be too useful. I would have liked to seen them at 2 MOA intervals. Below is a picture describing the L5 reticle, you'll get the idea. If you have a ballistic app with the L5 in it, it makes using the reticle much easier.

20" plate at 200yds on 16x 

  My favorite aspect of the L5 scope is the turrets. Being 1/8 MOA allows you to precisely adjust your zero. The turrets also lock down so they can not be turned. To adjust the scope, you must pull out on the adjustment knob, it will move out about 1/4". Then make your windage or elevation adjustment. And push the turret back down to lock it in place. I tried grabbing on to them tightly when locked, and could not turn them. Another nice feature of the turrets is the little rubber raised grips on the turret itself. The power zoom adjustment also has these raised rubber grips, but the one at 4x is slightly higher. Making it so you can reference the power adjustment knob. As with almost all scopes with target style turrets, they are resettable to zero. just take the supplied allen wrench, loosen the screw in the middle of the turret, pull cap up, reset to zero, push back down, and tighten the screw. One slight problem I noticed, the turret cap doesn't always go exactly back to zero. It will be close, but the 1/8" adjustments must be finer than the turrets cap threads. Don't get me wrong, the scope tracks fine, and will adjust back to zero, just not the cap. Speaking of tracking, I had no problems moving the turrets 2 turns out and then back to zero. The shots were still where I expected them. I did not however do a true scope tracking test.

  The clarity of the L5 is pretty good. They state a 92% light transmission, I can't test it, so I'll go with their spec. When having the magnification down at 4x, everything was sharp and crisp. Even at 12x, the clarity still surprised me, especially for a scope in this price range. Now at 16x, you could start to see a small haziness. It was better than I expected, but still noticeable. I also shot it in 100 degree heat, the mirage off the barrel didn't really seem to make it any more hazy either.

Zero misalignment and raised index on zoom adjustment

  After shooting quit a bit with the L5, I don't want to have to return it. But I would like a little more magnification on this particular rifle. I wouldn't hesitate to send people I know over to Lucid Optics. They offer some decent optics in the "not over the top expensive" category. I would also like to see them manufacture a scope with a first focal plane reticle. Go check them out if your in the market for a good sub $450 scope.

Firearms Insider Reviews - 8 Key Points

Claim to Fame:

Quality scope with a useful MOA reticle

Target Market:

Hunters, target shooters, or basically anyone wanting a 4-16 scope

FNBs (Features & Benefits of this product): 

  • 4-16 power
  • 30mm tube
  • 13.25" long
  • 18 ounces
  • 44mm objective lens
  • Waterproof  
  • Fogproof
  • Shockproof up to .338 Lapua
  • Side parallax adjustment  
  • Multi coated optics
  • L5 etched reticle
  • 1/8 moa adjustments
  • Lockable turrets  
  • 50 moa adjustment range
  • Comes with Flip caps

What other aesthetic options or finishes are available?

6-24x50 also available

What others are saying?:

M. Cotton: 5/5 stars at Amazon

Great scope for not a lot of money.

I was a bit put off at first because I knew nothing about Lucid Optics. Well, I was very pleasantly surprised. The glass is clear and bright the turrets lock and click very solidly. One thing I initially had concerns with, is how fine the reticle is. The literature says the center dot is 1/8th MOA, so are the stadia lines. I had trouble seeing the hashmarks until I focused it for my aging eyes. I can see them fine know. The scope came with flip caps, the front one is fine, the rear one doesn't fit very tightly. I used a couple of small spots of clear silicone to fix it in place, it stays fine now. All in all the scope does everything I hoped it would. I would buy another if I needed one.

wlbooth: 5/5 stars at Brownells

BEST SCOPE FOR THE MONEY! HAND'S DOWN!

Dollar for Dollar you can not beat Lucid scopes! I'm so glad I came across these scopes about 6 months ago, And I challenge Anyone to find a better scope for the money. It Can't Be Done. Period!!

Link to other reviews:

Guns 111th 

Price point:

MSRP = $419.00

Retail = $349.99 at Brownells

$328.99 at Amazon

I need it now! Availability:

Lucid, Amazon, or Brownells

Our Rating:

Pros: 

  • Clear glass 
  • Target turrets
  • Etched L5 reticle
  • Turret locks
  • 1/8 moa adjustments
  • Price
  • Ability to set turrets to zero
  • Raised index on magnification ring
  • Lifetime warranty  

Cons:

  • Slightly fuzzy at 16x
  • Zero mark doesn't always align with line on scope body
  • Windage marks at 4 moa intervals

Score: 8.0 Great

 

Chad's Favorite link: U.S. Tactical Supply

 

Thompson Tactical Gun Belt

   Thompson Tactical is a small leather shop specializing in custom belts. You can find their belts at leathergunbelt.com. When I say they make custom belts, it means they craft them by hand, and the craftsmanship shows. Their gun belt is a double layer, hand stitched belt. They also offer standard, single layer belts. 

  Now that we know something about Thompson Tactical, lets get into the great gun belt that they so graciously sent me. The belt is made from products purchased in the USA. This includes the full grain leather, the various buckle options, etc. When ordering the belt, one can also decide the color of the belt, ranging from tan to black and even mossy oak. Another nice touch is being able to select what color thread you want the belt to be stitched with, either single or double stitching options. My favorite option is the ability to have a kydex insert in the belt. The kydex adds a slight stiffness, but its real advantage is that it keeps the belt from stretching over time. 

  When I learned that Thompson Tactical was sending me a belt, I immediately went and ordered one. My belt is 1.5" wide, black, has a stainless non-roller buckle, single stitched with a kydex insert. I ordered the 1.5" belt because it is basically the standard for gun belts. Options are also available for 1.25" and 1.75" widths. Additionally, I opted for the kydex insert, because who doesn't want a little extra stiffness and a longer lasting belt? The kydex insert appears to be stitched in place on the back layer of the belt before the two sides are beautifully stitched together. The edges are burnished together for what looks like a single piece of leather. Chicago screws are used to hold the buckle on, and the logo is then branded on the inside. 7 holes are spaced 3/4" apart to give you adjustment. Following the instructions on Leathergunbelt, the measurement of the belt was spot on and I wear it on the 4th hole. 

  I have worn this belt everyday since it arrived at my house. All I can say is "Wow", this is by far the best gun belt I have seen, let alone worn. It has one slight flaw, that isn't really the belts fault. Some IWB clips are not deep enough to fit over the belt because of the belt being 2 layers thick. Other than that, it fits perfectly. It has the right amount of slip or flex, so it moves with you. The stiffness is perfect, as it holds a gun all day without the gun moving, or me even noticing the weight. The stitching is straight and beautifully done. And, best of all, at least in my opinion, it smells like a leather shop! 

  So now that you know about these belts. Head over and check them out at Leathergunbelt.com. The belt is really a piece of functional art. You can wear it 7 days a week,  even on Sunday,  and not be under dressed. It may take a long time to get one, but quality takes time. I doubt you will be disappointed. 

Firearms Insider Reviews - 8 Key Points

Claim to Fame:

Hand made leather gun belt

Target Market:

People needing a quality gun belt 

FNBs (Features & Benefits of this product):  

  • Full grain leather  
  • Hand made
  • Double layer
  • Kydex insert
  • Chicago screws
  • 1.5" wide
  • 25 year warranty  

What other aesthetic options or finishes are available?

 Tan, Honey, Cordovan, Brown, and Mossy Oak

What others are saying?:

Gary P. at Leathergunbelt.com

I got my first Thompson Gun Belt just about a month ago and I have not worn another belt since then. Today I changed the oil in my Jeep and my son's pickup and so I decided to wear a regular belt so I didn't mess up my "real" belt. Spent a couple of hours yanking my pants up and generally hating wearing a "regular" belt again. Couldn't wait to take a shower and change back into my real belt again. Even though Francesco makes a "gun" belt his belts are actually "real" belts as far as I am concerned! If I have to roll around in oil or mud I will probably wear an old "plain" belt, but for every day- whether I am carrying or not- I'll never wear anything but a Thompson Tactical gun belt!

Phillip N. at Leathergunbelt.com

I received my belt today. I am more than impressed with the quality of the belt. You have absolutely exceeded my expectations! Thank you for the obvious pride you put into your work. I will definitely spread the word.

Link to other reviews:

Mattsplat's Gun Reviews (YouTube) 

OUR RATING:

MSRP = $97, + $25 for kydex, + $10 for double stitching

I need it now! Availability:

Leathergunbelt.com

Our Rating:

Pros:

  • Full Grain Leather
  • Double layer
  • Kydex insert
  • Hand crafted  
  • Made in USA  
  • Lots of available options
  • 25 yr warranty

Cons:  

  • Thickness may cause problems with some holster clips
  • Wait time

 

Score: 9.0 Amazing

Chad's Favorite Link: ABC House Benefit Match

 

SuperBio IndestructiBelt

   As most people who conceal carry know, a good belt is a necessity. I had heard somewhere about the IndestructiBelt SuperBio by Daltech Force. So as any reviewer would do, I ask them if they would like me to review one. A few days later a brown one arrived for me to test. 

  The Daltech Force IndestructiBelt SuperBio belt is not your run of the mill carry belt. Instead it is made from a thermopolymer polyurethane with an internal polyester webbing. Basically this is a polymer belt that looks a lot like leather. But don't stop there. The SuperBio belt also is very strong, it is stated to have a 6000 psi tensile strength. The belt is also quite stiff, so don't worry about it sagging. I think you could carry just about any gun you wanted and not have to worry about it pulling on the belt. Since the SuperBio belt is made from polymer, it will resist oils, water, sweat, and other stuff that will destroy a leather belt. To clean the belt,  all you have to do is wipe it down with some soap and water. 

  As with most quality belts, it comes with Chicago screws to hold on the buckle. The one they sent me has a nice stainless roller buckle on it, but they also offer a brass buckle. The buckle can always be switched out if you don't like it. The belt comes with 9 holes spaced 3/4" apart. This comes in handy when adding or subtracting gear. At 5/32" thick it is about the same as a single thickness leather belt. Mine is 1.5" wide, but they also offer it in a 1.25".

  After wearing the SuperBio belt for awhile, I found it to be almost too stiff. It is just not as slick as a cloth or leather belt, so I don't think it moves with the fabric of your clothes as well. Did it support a gun? Oh yes, I even carried an all steel 1911 on it for a few days.

   As far as sizing goes, the SuperBio belt is easy to order. All you do is add 2" to your waist size. So for me I went with a 38 belt size because my waist is 36". With belt sizes ranging from 30" to 80", yes that is 80", Daltech Force makes it for just about any size person. 

  The SuperBio IndestructiBelt is a pretty good belt option. If you need something that resists harsh environments or you are looking for a very stiff belt, you might give this a try. It doesn't really look like leather close up, but from a foot or so away you can't notice. The belt will hold whatever you can put on it and is very adjustable to fit your needs.

   

Firearms Insider Reviews - 8 Key Points

Claim to Fame:

Tough Rigid Belt for CCW

Target Market:

Concealed carriers, competitive shooters, or those wanting a belt for harsh environments

FNBs (Features & Benefits of this product):

  • Thermopolymer Polyurethane

  • 1.25" or 1.5" width

  • Strong

  • Resists Oil, water, Sweat, or other harsh environments

  • Zero Stretch

  • Will not Sag

  • Stainless Buckle

  • Chicago Screws

  • Large sizes available

What other aesthetic options or finishes are available?

What others are saying?:

Dan @ DaltechForce 5/5 stars

Can't believe how well this belt held up! I've had my first one for almost two years and it has been through everything. It has been on multi day hikes with dripping sweat, it has swam in salt and fresh water, its my daily belt for both my office job and my weekend belt for recreation. If I showed you this belt you would swear I just pulled it out of the packaging! Fortunately/unfortunately I've lost a significant amount of weight in the last year and I am back to purchase this belt again! One thing that I would recommend is to put some thread lock blue on the screws as soon as you get it. I've read of others losing a screw and they include a spare, but better safe than sorry. Otherwise a really maintenance free, good looking, and long lasting belt that is rigid and does a great job holding my CCW without it flopping about.

Amazon reviewer 5/5 stars

This is a great belt! I love it! I like to carry a lot of stuff in my pockets and on my belt. With this belt, I no longer have to keep hiking my pants up. I wish I had ordered one sooner. It really does make a big difference.

 

Price point:

MSRP = $69.99

Retail = $59.99 on Amazon

I need it now! Availability:

Daltechforce or Amazon

Our Rating:

Pros:

  • Strong

  • Won't stretch

  • 9 holes at 3/4" spacing

  • Stainless roller buckle

  • Chicago Screws

  • Will not sag

  • Resists about anything it will come in contact with

  • Easily cleaned

Cons:

  • Too stiff

  • Doesn't move like Fabric or Leather

  • Doesn't really look like leather (But no one will know)

Score: 7.5 Good

 

Chad's Favorite Link: AR-15 Podcast

MDT LSS-XL Chassis

  After winning a Savage 11 at a raffle, I was looking around at what I could do to it. I started looking at chassis for it and ran across Modular Driven Technologies (MDT for short). I contacted them and they said they would send me a chassis for review. They sent me the LSS-XL, their new lightweight stock, and one of their AICS pattern magazines. 

  The LSS-XL is an all aluminum chassis that can use AR stocks and pistol grips. It comes either cerakoted black or FDE. It can use their stock also, which I'll talk about later. Since the chassis they sent me was for a Savage, I'll talk about it, but all of the LSS-XL's are basically similar. The first thing I noticed was the nice sized paddle magazine release. It has good spring pressure and is easily accessed to remove a used magazine. I also noted that it came with a sling swivel stud mounted, perfect to attach a bi-pod on. Next up is the trigger guard that has enough room for gloved hands, but is could be larger.  The stated weight is 1.8-2.1 lbs, which is just the chassis without a stock or pistol grip. My scale broke, so I am taking the weight off of the MDT website. Now the LSS-XL has a longer forearm than the LSS, but it is about the same length as the stock forearm. Even though the chassis is about the same length as the factory stock, it is much thinner and is flat on the bottom and sides. It also has plenty of mounting holes on it. These holes are spaced to fit Magpul L3 or L5 rails. Of course MDT makes rails to fit also. On the Savage style chassis, it has a slot in the side above the trigger. This slot is for Savage actions with a bottom bolt release. After installing the LSS-XL, to remove the bolt, you have to now put a pin, nail, screwdriver, or whatever in this slot and move it rearward to remove the guns bolt. The chassis also comes with a little spacer washer, that you install on the front bolt, depending on which action length you have. Older Savage's have a slightly different bolt spacing on the action than the newer versions. Using a rounded inlet with flat spots, for the action to ride on, this design is said to aid in accuracy and strength. Along with this system, the chassis can accept barrels up to 1" diameter while still free floating the barrel. 

  One of the great advantages to the MDT LSS-XL is it ability to accept the AICS style magazines. The stock magazines that come with the Savage are junk compared to the MDT magazine. MDT's magazine is polymer and holds 8 rounds of .308, .243, .22-250, or 6.5 Creedmoor. They also make a magazine for the smaller .223 rifles. My rifle is in .243 winchester, and the magazine function was flawless. I am also able to get 9 rounds in the magazine and still have it function. Being that the LSS-XL uses the AICS pattern, I also tried a Magpul 5 round AICS magazine. It did not lock in place at first. I modified it slightly by removing some plastic in front of the feed lips and now it works also. Basically I made it look like the MDT magazine. 

  Along with the chassis, MDT also sent their "Skeleton Rifle Stock Lite." This stock is meant to compliment the chassis, and it does a decent job of it. The stock is adjustable for length of pull and cheek weld. Now it does not have infinitely adjustable screws, instead it has notches in the riser and buttplate mounting stems. The buttplate and riser are moved by pushing an elongated button, and then moving them to the desired adjustment. I really liked this button system as it was easy to use, and held the plates in firmly. MDT also makes the stock out of aluminum and it is cerakoted to match the chassis. Another nice touch on the stock is its ability to accept mounting rails like the chassis. This makes it possible to install a monopod or such device under the stock. As with most stocks these days, there are also built in sling swivel cups. One problem I had with the lite rifle stock was the rear but pad and cheek riser get in the way of cleaning your rifle. Even if you take the cheek riser off, the design makes it impossible to run a cleaning rod straight through the rear of the rifles bore. If you want to do this, you must actually remove the stock completely. I did not have the same problem when using a standard AR stock. 

  There are a couple of items to note. The stock's length of pull was too short for me even when the buttplate was fully extended. And there is no radius where the top of the grip meets the stock. AR grips with beavertails don't really work. So it kind of pinches your hand between your thumb and forefinger. I noticed it more with a collapsible AR stock. The MDT stock was way less noticeable. 

  The MDT LSS-XL chassis, Skeleton rifle stock lite, and magazine make for a really nice stable shooting platform. MDT offers these chassis for lots of different rifles, and all of them at a very reasonable prices (for a chassis system). 

Firearms Insider Reviews - 8 Key Points

Claim to Fame:

Lightweight chassis system. Uses AR parts

Target Market:

Precision rifle shooters, varmint hunters, or anyone wanting a stable shooting platform.  

FNBs (Features & Benefits of this product):

  • Drop in chassis

  • All aluminum

  • Cerakoted

  • Improves accuracy

  • Free floats barrels up to 1" in diameter

  • Weighs about 2lbs

  • Uses AR-15 stocks and pistol grips

  • No Bedding needed

  • Uses AICS magazines

  • SRS Lite stock is adjustable for length of pull and cheek weld

What other aesthetic options or finishes are available?

Flat Dark Earth

What others are saying?:

GREAT CHASSIS FOR SAVAGE LA

LSS-XL for Savage Long Action: This is a great chassis system. Form, fit, and function ate all very nice. The chassis is very light so for the heavy recoiling calibers, it is something to consider. The machining is done very well. Cuts are precise and the finish is very uniform and professional. My rifle is sub MOA with this chassis and I think it will drastically improve as I get more comfortable with the setup. I always shoot from prone so taking me out of the equation to eval the chassis can be difficult. My rifle comes in at 14.5lbs w/ Leupy Mark 4 16x, Leupy steel rings, steel one piece base, 26" bull barrel 300WM, bipod and MagPul MOE stock. Great chassis at almost half the cost of many others.

EXCELLENT PRODUCTS

The products were high quality and my R700BDL 6mm Rem fit like a glove. Very easy and quick installation. I am considering also getting the LSS-XL for my Savage 12 Low profile.

Price point:

MSRP = $499 for the LSS-XL

$279.99 for the SRS Lite stock

$39.99 for the Magazine

Retail = $499 @ Tactical Works

$279.99 @Tactical Works for the SRS Lite stock

$39.99 @ Brownells for the Magazine

I need it now! Availability:

Modular Driven Technologies

Our Rating:

Pros:

  • Very cost effective

  • Models available for many different rifles

  • Uses AR-15 stocks and pistol grips

  • Lightweight

  • Uses AICS magazines

  • MDT magazine works well

  • Swivel stud pre-installed

  • Sling swivel cups in stock

  • Push button adjustment on stock

  • Large trigger guard

Cons:

  • Small fore-end

  • Slight pinching of hand

  • Short length of pull with SRS Lite stock

  • Can't clean bore without removing SRS Lite stock

Score: 8.0 GREAT!

 

Chad's Favorite Link: U.S. Tactical Supply

 

Manticore Arms Nightbrake Review

The Manticore Arms Nightbrake for the AR-15 pattern rifle is an interesting little break. Designed by Sven Jonsson, this break comes with a crush washer and the break in the box. Going from an A2 birdcage style flash hider to this seems, at first, like going from driving a go kart to driving a muscle car. The Nightbrake threads on easily to any 1/2" x 28 threaded barrel and is relatively easy to tune. The myriad of ports allow for greater recoil reduction, while the absence of any ports at the 12 o'clock position allow for a complete sight picture that is free of any gasses or fireballs directly in your line of sight. There is a notable absence of ports on the lower half of the break to help erase any dust signature that may happen when firing prone or in any type of dusty environment such as a desert or abandoned building. The Nightbrake itself is 1.875" long, and weighs in at a mere 2oz. You'll notice that the length would not be suitable for someone looking to buy a 14.5" barrel and pin this on to make legal length. Now, having covered the basics, lets delve in to the fun part!

After attaching the break to my rifle and making sure that it was tuned correctly, off to the range I went. I had only one other break on this particular AR build, so It was quite a difference when I shot my first magazine at my local indoor range. Shooting some basic Freedom Munitions .223 I was surprised at the fireball that came from the first few rounds. There is quite a noticeable drop in recoil and muzzle rise when using the Nightbreak. The reduced felt recoil helped me to get back on target quicker for more follow up shots. The reduced muzzle rise was substantial compared to the A2, and some of the other breaks out on the market. All this does come at a cost, depending on how you look at it. Being a compensator and not a flash hider, the Nightbreak does nothing really to reduce sound and flash. The concussion emanating from the Nightbreak is extremely loud and somewhat obnoxious for those in the stalls next to you. Not something I was too concerned with, but something to consider depending on your environment. The flash was brilliant! I had a friend capture it on video and the fireball reminds me of watching an 18th century cannon go off and the flash at the muzzle. After an afternoon at the range putting it through it's paces I was sold.

Overall, the benefits far outweigh any of the cons mentioned above. The Nightbreak turned out to be the exact compensator I was looking for in this particular build. The sound, fireball, and looks make this a great addition to any AR pattern rifle. The reduced recoil and muzzle rise add to this already fun break making it a must have for anyone looking to replace their birdcage or find a new break to breath new life in an old rifle. At $58 on Manticorearms.com, the price is just right and worth every penny in my book.

Firearms Insider Reviews - 8 Key Points

Claim to Fame: Superb compensator for the AR-15 pattern rifle

Target Market: Target shooters and competitive shooters looking for an upgraded compensator at a reasonable price point

FNBs (Features & Benefits of this product):

  • Weight 2oz

  • No ports on the underside to prevent dust signature

  • Will clear any bullet up to .30 caliber with thread pattern of 1/2” x 28

  • Mitigates muzzle rise from the ports around the top 270 degree arc

  • Black oxide finish to prevent corrosion

What other aesthetic options or finishes are available?: None. Black oxide finish is the only option at this time.

What others are saying?:

“An excellent brake for the money” TheGunWire.com
“ Manticore’s NightBrake is designed primarily to keep the muzzle nice and steady without increasing flash or concussion, and it seems to do a solid job at this — well, except for bare muzzle-like fireballs out the front — in a compact, lighweight, and aesthetically-pleasing package. The two “strips” of ports on the bottom are solid to keep you dust-free when shooting prone and to allow the open ports on top to compensate for muzzle rise. Machining and finish are both fine, but not exemplary. It looks like QD mounts that work on an A2 birdcage would work on the NightBrake.” The Truth About Guns

Link to other reviews: Mr Guns N Gear video review

Price point:

MSRP = $57.95 

Retail = $57.95 

I need it now! Availability: The Manticore Nightbrake is available from Primary Arms, or directly from Manticore Arms.

Our Rating:

Pros:

  • Also available for other calibers

  • Very effective at mitigating recoil

  • Price point low enough for anyone to afford

  • Extremely well made with proven finish

  • Lightweight for those looking to finish off those lightweight builds

  • Counts as 922r compliant part

Cons:

  • Length prevents use on barrels shorter that 16” without a stamp

  • Only available in black oxide

  • Flash could hinder sight picture in low light conditions

  • Concussion could annoy fellow shooters at the range

Score: 8.0

 

Alex's Preferred FFL: Atlanta Range and Ordnance

KE Arms DMR trigger

  KE Arms has been bringing out some useful products for the AR 15 style rifles. One of those is their DMR trigger. It seems that everyone has been coming out with AR triggers lately. So what makes the DMR different? Well, lets see if I can help answer that question. 

  Everyone seems to want the best trigger they can get. I am no exception. The DMR trigger does a fairly good job in the cost per performance category. When I received the trigger, the pull weight measured 4.25 lbs. KE Arms states it as a 4.5 lb pull, with an adjustable reset. The reset adjustment also adjusts the pull weight. So if you screw out the adjustment, you get a lighter pull weight and a lighter feeling reset and vice versa. So if one wants a really positive reset, it come with a harder trigger pull. One can actually adjust the trigger pull low enough so that the trigger will not reset. My trigger had an adjustment from about 3.25-6.5 lbs. I set it at 3.75 lbs because the reset was still acceptable to me. 

  The DMR trigger is of the drop in design. I did have to remove the safety to install it, but for anyone familiar with the AR 15, this is pretty easy. To install the trigger; remove the old one, remove the safety, drop the DMR trigger in, slide the new provided trigger pins in. Reinstall the safety. And then tighten the 2 set screws,  these put pressure on the trigger pins to hold the trigger in place. Now you can function test the trigger. You can view the installation instructions here: DMR Trigger installation.

  One of the things that makes the DMR good, is its feel. I liked the shape and feel of the trigger shoe. It is curved, but not as much as a stock trigger. It has basically no noticeable take up. A crisp break, with very little over travel. The reset however is a little gritty and somewhat kind of mushy. It is however a very short reset, so unless you are resetting the trigger extremely slow, you will probably not notice. The reset feels this way even if it is adjusted for a stronger pull/reset, it is just harder to notice because of the greater force of the reset. 

  The only problem with the DMR trigger, is that it would not consistently set off .22lr. About 1 in 10 would not fire because the hammer didn't have enough force to set it off. Imported steel case 5.56 ammo worked fine, as did all the other ammunition I put through it. So I wouldn't recommend it as a duty trigger. But for anything else, it works great. I would probably also recommend some sort of anti-rotate pins, just in case the set screws that hold the trigger in place come loose. 

  As for KE Arms and their DMR trigger, it falls in line with other manufacturers in the same price range. I would not recommend it for a duty rifle because of the lighter hammer energy. But the trigger feels good. It is no 2.5lb trigger, but it was not designed to be. The pull weight felt lighter to me than it actually measured. If your in the market for an AR trigger, the KE arms might be what your looking for. 

Firearms Insider Reviews - 8 Key Points

Claim to Fame:

Drop in single stage trigger for AR 15 style rifles.  

Target Market:

Anyone looking for a better AR 15 trigger. 3 gunners, target shooters, sportsman, varmint hunters, or anyone who wants to upgrade their trigger.   

FNBs (Features & Benefits of this product):

  • 4.5 lb adjustable reset
  • Drop in installation
  • Melonite coated
  • Crisp break
  • Minimal over travel
  • Single stage
  • Made in USA

What other aesthetic options or finishes are available?

Black Melonite

Titanium Nitride

What others are saying?:

Awesome trigger 5/5 stars from Jared B on gotammollc.com

I now have 3 of these triggers for my AR10 & AR15, Im super excited got ammo now carries these because they're right down the road from me. I also own a Velocity trigger and I like these much more, the break is super clean & the adjustable reset is awesome!!! no complains here. 

Link to other reviews:

The Truth about Guns

Price point:

MSRP = $169.95

Retail = $154.95

I need it now! Availability:

KE Arms or sometimes Amazon

Our Rating:

Pros:

  • Adjustable pull weight / reset 
  • Crisp trigger break
  • Virtually no take up
  • Very little over travel
  • Easy installation
  • Allen wrenches included for adjustment and installation 
  • Made in USA  

Cons: 

  • Rough / mushy reset
  • Not enough hammer energy to consistently set off .22lr 

Score: 7.50 Good

 

Chad's Favorite Link: Saddle Butte Machine Gun Shoot

 

Alien Gear Cloak Mod OWB Holster

If you're like me, you probably have accumulated more than a couple drawer's worth of inside the waistband holsters. It just happens when you start shooting handguns and carrying them in different fashions. Usually, the collection starts with cheap holsters off the store shelf that (if used enough) also seem to carry a shelf life. Hopefully the next holster you acquire is a little bit nicer, and so on until you end up with a cardboard box full of neglected holsters, to guns you might not even own anymore. It's okay, it happens everyday and I am especially guilty of it.

Thats why i was so was excited when Alien Gear asked us to give their latest outside the waistband holsters a try. Since reviewing both the Cloak Tuck 2.0 and Cloak Tuck 3.0 inside the waistband holsters, I have been eager to upgrade my range bag with an OWB paddle holster in the same level of quality. Meet the Cloak Mod OWB holster!

The all-new Cloak Mod OWB holster is the result of you and I. What I mean is specifically in the last couple years the industry and consumers have really directed product trends towards simpler design and more modular/flexible features. You can see this taking effect in almost every product type in the firearms industry today, and you will definitely be seeing it more and more in the holster game in the coming months. 

While Alien Gear has had an OWB holster available for some time in the Cloak Slide OWB holster, the design felt like an augmentation of their Cloak Tuck holsters just repurposed for outside the belt. It still works and has good retention, but the balance between function and form was a bit off. So after spending over a year in development, Alien Gear arrived at a new design to be the next evolution of their OWB holsters.

The Cloak Mod is a stronger holster overall. The buff in structural integrity comes from the spring-steel flex plate at its core. This new addition is what made the biggest leap forward between the Cloak Tuck 2.0 and 3.0 IWB holsters, as it grants the rig more strength and flexible support than any other material without adding unnecessary bulky layers. The outershell is molded to fit your pistol shape, but its the steel plate that gives when you holster the firearm, applying even pressure against the shell and keeping your gun retained firmly. This is where traditional kydex holsters lack, the front and back shell is merely a pocket with tight tolerances that holds the gun in place. Eventually after regular wear and tear that comes with use, the tolerances expand and retention decreases. This is one of the only times you'll see a grown man using a hair dryer... to heat up the kydex and manually reform it to retighten those tolerances around your gun. 

Of course a bare steel plate pressing against your pistol's slide and frame would be a terrible idea, which is why Alien Gear's engineers added a layer of rubber-like material to act as a buffer. They are calling this a thermo elastomer retention membrane, but I'll call it THERM for short. So THERM rests between your gun and the steel flex plate, which gives alittle when you insert your gun and helps "snap" it into the contours of the molded outer shelf when fully inserted. Retention can then be further adjusted by loosening or tightening the four main flathead screws, so you can find just the right amount of grip you prefer for your gun and your intended use. 

Of course just like every decent OWB holster (actually ANY holster in general) is cant angle adjustment. Any holster maker worth their salt should accomodate the end user's comfort and preference. Some guns draw better from a forward cant, and some shooters prefer a rearward cant. This preference can really differ from gun to gun, as a larger framed gun may need better leverage to draw, especially if you were blessed with small arms.

Not to rest on their laurels, Alien Gear also integrated a wider opening in the mouth, designed to help guide the muzzle of your gun into the rest of the holster. I really felt the benefit of this feature in both the Sig P938 and Glock 19 versions I reviewed. While the general rule of thumb is "draw fast, reholster slow" to prevent fumbling around especially without breaking eye contact with your surroundings, having a flared mouth makes a huge difference, especially larger guys with and extra tire in the old midrift that makes reholstering without looking an extra challenge. 

Finally I'll get to the holster's attachment hardware. You are provided with both a paddle and a belt slide... Yet another growing industry trend I praise the gun gods for! Using the same hardware, you can select whether you want your Mod holster slid onto the belt or clipped over with a curved paddle. If you aren't sure the difference, try both! The Alien head shaped paddle (poor, poor E.T.) whose face gets smothered against your hip is designed wide so as to spread surface contact and pressure and prevent discomfort. I can tell you the paddle is great for shooting at the range stationary or in competition running around from target to target. When carrying outside the range in a defensive role, the paddle's built in retainment lip keep unfriendly folks from yanking your holster off your belt.

The slide is a bit more classic, and requires the user to thread a belt through the slide inbetween your pant's belt loops. This method is secure and great for concealed carrying under a cover garment, as well as on the range. Alien Gear's slide isn't just a piece of plastic either, its a flexible rubber that will help grip the belt and reduce excessive friction while still being comfortable without any hard edges to jab your when bending over. The real difference between the paddle and the slide boils down twofold: You can use a paddle without a belt (over the waistband) and the large curve surface against your hip gives better leverage when drawing. The slide ultimately is more secure since its on until you remove your belt but decreasing the bearing surface to just your belt in a smaller rectangle will cause the holster to hang more, especially with heavier guns. Since I will primarily be using the Glock 19 at the range and the Sig P938 on the streets, I've chosen to keep them in paddle and slide configuration, respectively. 

For the cherry on top, the Cloak Mod’s holster shells are fully swappable... just like the Cloak Tuck series. This means you can easily swap out your shell to match the firearm you want to carry... literally remove four screws, replace shell, and retighten! Not only that, but Alien Gear will give customers with the Mod holster free shell trades for life. If you ever sell or trade off your handgun for a different model, just send back the old shell and let them know the new model to replace it, for life! (hello laser blasters).

They're so confident with all their holster products, Alien Gear has an "Iron-Clad Triple Guarantee" that covers your OWB holster with a replacement or repair if it breaks for any reason. Plus with the 30-day test drive, you can return the Mod to Alien Gear with no fuss and no hard feelings. 

Putting the Mod in modularity, the Cloak Mod Holster is fantastically priced and featured holster option. I'm glad to see the price point for these stay low enough for new gun owners and less frequent shooters to have access to a very high quality holster without spending more than 3-4 boxes worth of ammo. Working in retail I saw a lot of first timers go for the cheaper nylon holsters because A) it was in the store and convenient to toss in the cart and B) They're inexpensive and no value is placed in the tool that keeps your gun secure and not in the dirt. It's like buying a $600+ rifle and mounting a $50 scope with $10 rings... put value in the things that keep you and your shiny investment safe, because it will make using your firearm more enjoyable by 10 fold, I promise!

Pro-Tip: I tell everyone interested in giving Alien Gear a try to take advantage of their 2 holster combo deals. If you're like me and need to have holsters for several different handguns,  $47.88 a pop for the Mod OWB adds up quite a bit. However, instead of $72 for two holsters, two holsters can be purchased as a combo for as little as $49.88. Both holsters come with sets of durable clips and interchangeable shells for the guns of your choice. This not only assures consistency in your holster usage for all your guns, but increases resale value if you ever decide to sell a gun with the high quality holster you got for a steal!

FIREARMS INSIDER REVIEWS – 8 KEY POINTS

Claim to Fame: After spending over a year in development, our OWB paddle holster is ready to be carried by those looking to protect themselves on a daily basis.

Target Market:  Handgun owners, open carry & conceal carry, recreational shooters

FNBs (Features & Benefits of this product):

  • Swappable Holster Shells
  • Flexible spring-steel core plate provides strength and support
  • Layer of thermo elastomer for added retention
  • Wide open-mouthed design for easy reholstering
  • Includes paddle and slide for user configuration
  • Iron-Clad Triple Guarantee

What other aesthetic options or finishes are available?:  Black only

What others are saying?: 

PRICE POINT:

I need it now! Availability: Alien Gear

OUR RATING:

Pros:

  • Swappable shells let you carry more guns in your collection without buying a whole second holster
  • Both paddle and slide hardware is adjustable for cant angle
  • Paddle is wide enough to spread bearing pressure across hip while fitting between belt loops
  • Slide is made of rubber with a round friction button to help control position on belt

Cons:

  • Ride height not adjustable
  • Paddle one size fits all so maybe large for most CCW belts
  • Layered design leaves visable gap between backer and plate, possible concern of debris or rust overtime.

SCORE: 8.0 GREAT

 

 

Featured FFL:

For FFL services I choose Promised Land Firearms in Toulon, IL.

Ryan's Links:

Gun & Gear Review Podcast
Hunter of Design

FN - FNX 45 Tactical

FNX 1.jpg

FNX 45 Tactical has a few slight modifications from the FNP it is based on. The FNX uses different magazines and frame slide and barrel are all tweaked enough parts are not interchangeable. The FNP was designed for the Joint Combat Pistol trials in 2006 some of the requirements of it are: chambered for .45 ACP, having an integrated Picatinny rail, including day/night sights, a high capacity magazine, and being capable of accepting a suppressor. Understanding that the FNX design sources form those requirements, we have the really cool FNX 45 Tactical.

On paper this gun is fantastic it is fully ambidextrous is suppressor and slide mounted optics ready right out of the box with 15 +1 capacity of 45ACP. In the really nice case the gun comes with 3 mags and 4 different blackstraps but only 2 sizes the others are in an alternate texture.

The FNX comes standard with 4 magazines, differing backstrap sizes and textures and a case to carry it all.

The FNX comes standard with 4 magazines, differing backstrap sizes and textures and a case to carry it all.

The FNX is a hammer fired double/single action gun with a decocker that is activated when the safety is pulled below the fire position. The FNX shoots like a dream with the incredibly smooth smooth trigger pull and aggressive stippling to maintain a good grip in adverse conditions. The FNP/FNX 45 tactical was one of the first guns to come from the factory ready to accept slide mounted optics. Having worked with a slide mounted red dot on the FNX I have become 100% sold on slide mounted optics this is a feature all handguns need to start offering. With 15 round 45ACP mags we come to the highlight and glaring flaws of this gun.

You can see the comparison in weight between the fully loaded FNX 45 Tactical and a GI style 1911 pistol.

You can see the comparison in weight between the fully loaded FNX 45 Tactical and a GI style 1911 pistol.

The fame is too weak with a good grip on the frame it will flex just enough to hinder the magazine from dropping free. Cold weather also causes the frame to shrink enough to prevent the magazines from dropping free. There is a video on Youtube of the frame flexing like silly putty in summer heat. I have not experienced that degree of flexing but just enough to cause issues when using the gun in competition. Also in some circumstances magazines bind when loading. The bind issue is caused when the magazine is inserted at a slight twist to the frame or at a slightly forward cant the front of the mag will catch on the magazine release assembly. To some people issues changing mags are not a deal killer but in competition where seconds count having to go back to strip the empty from the well before reloading and the possibly of a mag hangup upon reinsertion just wont fly. In the days where the experts still teach the crush grip as proper technique this kind of flaw is unacceptable on a gun that will be used as anything beyond just a range toy. I want to love this gun for its unique and forward looking design but the fame/magazine issue relegates it to being an extremely overpriced toy.

Video review of the FNX 45 Tactical

Firearms Insider Reviews - 8 Key Points

Claim to Fame: High capacity, optics, and suppressor ready handgun.

Target Market: Military, Enthusiasts looking for an optics and suppressor ready handgun.

Key Features:

•        Operation: Double-action 10lb /Single-action 3.5lb

•        Magazine: 15 rds.

•        Weight: 33.3 oz. (empty) 33.75 oz (with red dot) 44.95 oz (loaded with red dot)

•        Barrel Length: 5.3″ (with .578x28 RH barrel end thread pattern)

•        Overall Length: 7.9″

•        Raised night sights for suppressor use

•        Two interchangeable backstraps

•        MIL-STD 1913 accessory mounting rail

•        Fully-ambidextrous decocking/safety levers, slide stop lever and magazine release

•        Includes two mounting bases for optional red-dot electronic sights

What other aesthetic options or finishes are available? Flat Dark Earth, Black

What others are saying?: "Accuracy, reliability, ergonomic excellence, fifteen round capacity, tritium sights and suppressor-readiness makes the full-size $1300 FNX-45 Tactical a superb value. This is my first FN firearm. Based on my experience with this one, it won’t be my last." - Jon Wayne Taylor, The Truth About Guns

"FNH set out to create a tactical marvel, instead they created a gun with an incredible amount of personality, ease of use for a hammer-fired gun, shoot ability and an extensive cool factor at a price that isn’t cheap but very competitive. The FNX-45 Tactical is a home defense powerhouse if you push it to its tactical potential by adding a light, RMR and suppressor, and I think it’s one of the coolest full-sized .45 ACPs on the market today." -Colion Noir, Americas 1st Freedom

Price point:

MSRP = $1,299.99

Retail = $1,050+

I need it now! Availability: Available from many retailers and Gunbroker.

Our Rating:

Pros:

•        Optics ready

•        Suppressor height night sights (dual color)

•        Threaded barrel

•        High capacity 15 +1 45acp

•        Full ambidextrous 

•        Great fit and finish

•        Fantastic case

Cons:

•        Size

•        Weak frame

•        Magazine catch

•        Magazine availability and cost

•        Requires custom mag holders

Score: 6.0

Matt's links:

Geeks Gadgets and Guns Podcast

LFD Research

Springfield Armory 1911 Loaded Stainless

Photo Credit: Springfield Armory

Photo Credit: Springfield Armory

It’s with heavy heart that I write this review. Springfield Armory has a great history. It’s truly a part of gun culture, real americana. From the Trapdoor, to the M1A, not to mention the iconic 1903. These firearms have shaped the shooting landscape. I, myself, competed with the Springfield M14/M1A as a military / civilian competitor. I have a long history with that rifle filled with happy memories. I’ve literally disassembled and assembled them with my eyes closed. I had equally high hopes for a beautiful stainless Springfield 1911. Those expectations were shattered. This review is not going to be a rave.

I have been testing this handsome stainless, loaded, Springfield 1911. What could go wrong. I mean, it’s a classic American work horse, metal on metal, stainless, hardwood, American made, full size handgun by a classic gun company. Well, as it turns out, quite a lot can, and has, gone wrong. At least this gun is heavy so you could beat someone to death with it, since it’s likely not to work.

First, for a gun to be good, it has to be reliable. This 1911 failed horribly. Name a malfunction, and this pistol had it. The most common malfunction was the slide not going all the way into battery after a round had been fired. At first, I assumed it was the ammo, but these rounds worked in other “lesser” at least less expensive pistols. They were 230 grain ball FMJ. I have also tried 185 gr flat points. Not to mention expensive 230 Grain Federal HST.

Next, I assumed that it was the magazines. I used the factory magazines with poor results so I tried factory Colt 7 Round magazine.  I ended up trying 5 magazines with not one being reliable. Failure to return fully into battery was the most common problem, sadly not the only, or the worst, problem. I was happy to get a full magazine to feed. It also had double feeds & stove pipes. New springs were put into the pistol. These did nothing to help.

Even more disturbing was while my wife and father in law were in the middle of a shooting session, the front sight fell out. Yep you read it right the front sight fell out! I wrote to Springfield since it should have been covered under warranty. They still, to this day, have never gotten back to me. It’s been months. To make things worse, this 1911 has its own proprietary pinned front sight. A new one had to be installed (owner's expense). The 1911 has sights now but it's still is not very reliable.

I will keep this review short mostly because I have not been able to get this weapon to function well enough to really train with it. Like I said, Springfield is a classic American company and it is entirely possible that this is just a lemon. The next one one on the assembly line may have been fine, maybe not. But I will say this, with the trouble that I have had with this firearm, and the lack of customer support I have experienced, I'm not likely to spend money on another Springfield 1911. There are so many good 1911’s, especially in this price range (and many that are far cheaper) that work so much better than this one.

I realize that this review may upset some people. Trust me I'm not thrilled, I have that expensive pistol sitting in my gun cabinet doing nothing. I know there may be a lot of Springfield fans that are up in arms, they may have a Springfield 1911 that runs great. But, with my experience, I cannot recommend a Springfield 1911.

Thankfully, I am very blessed to have many pistols; if I knew I was going to get in a gunfight today, this would be the very last handgun I would want grab out of the gun cabinet, that includes a .25 auto. I wonder how upset John Browning would be if I handed him this pistol?

P.S.  I sent this review to Springfield first before I published it. It seemed only fair. They did finally write back and said that I could send the pistol in and they would look at it. Now if they fix it and it comes back running right I will amend this and give it a fitting review.

Firearms Insider Reviews - 8 Key Points

Claim to Fame:

American Made Stainless 1911 with a legendary name.

Target Market:

Midrange 1911 buyers

FNBs (Features & Benefits of this product):

  • Full Size
  • SAO Single Action Only.
  •  7 round single stack
  • 3 dot sights
  • Stainless steel & Hardwood
  • Barrel Length: 5"
  • MSRP $334

What other aesthetic options or finishes are available?

Springfield offers a variety of sizes and finishes.

What others are saying?:

"" - Nick Leghorn, The Truth About Guns

Price point:

MSRP = $963

Retail = $899+

I need it now! Availability:

The Springfield Armory 1911 Loaded Stainless is available from a few retailers, but you may have better luck finding one through GunBroker.

 Our Rating:

(What we say about it) (Required)(Please add bullets before each item below)

Pros:

  • Stainless construction
  • Well balanced

Cons:

  • Horribly unreliable
  • Broke before I could finish the review

Score: 2.0

 

Tripwire Charging Handle

 

  AR 15 charging handles are really a dime a dozen. So when I run across something innovative, I have to try and review it. SinterCore is just the company doing that. They have introduced an ambidextrous charging handle called the "TripWire." It happens to be of the extended type with some cool features.

  After receiving the TripWire, I had to look it over. The reason for this is because it does not have your standard style moving latch. Instead it has a 3D printed carbon filled nylon latch. But what makes it innovative? Well, the latch is on a hinged pin with a spring and the handle/handles do not move or pivot. So all that one has to do is pull straight back on the handle. No pulling a latch or lever to unlock it, the latch just unlocks itself. The rest of the handle is 7075-T6 aluminum and hard coat anodized with some grooves cut in for better grip.

  One might wonder how reliable this design can be, I was. But as I have used the TripWire, I found it to hold shut just as well as any other charging handle. The handle does take a little more force at first to cycle the bolt. This is because you have to overcome the spring pressure holding the charging handle from moving. I also slammed my unloaded AR against the floor numerous times to see if I could get it to unlatch, I couldn't. And while doing this I could hear the bolt moving, so it passed my hold closed testing.

  I really like the design of the TripWire. It is lightweight, quality machined, and even 3D printed. Plus there are very few moving parts. Sintercore also told me that if I wanted a lighter weight spring to unlatch the charging handle, they could send one out. I thought it was fine and don't want the chance of the lighter spring making it easier for the charging handle to come unlatched. If you are looking for something other than the standard AR15 charging handle, give the Tripwire a chance.

  

Firearms Insider Reviews - 8 Key Points

Claim to Fame:

AR15 ambidextrous extended charging handle with no latch to manipulate.

Target Market:

Any one with an AR15 that doesn't like the tiny stock charging handle.

FNBs (Features & Benefits of this product):

  • Extended

  • Lightweight at 1.0 ounce

  • Ambidextrous

  • 7075-T6 Aluminum

  • Hard Coat Anodized

  • Carbon-filled Nylon 3D printed latch

  • 2.52" wide 

What other aesthetic options or finishes are available?

Black is it.

Link to other reviews:

The Firearm Blog

Price point:

MSRP = $65.00

I need it now! Availability:

SinterCore

Our Rating:

Pros:

  • Ambidextrous

  • Extended

  • Lightweight

  • Quality Machined

  • Essentially latch free / Straight pull design

Cons:

  • Will not fit AR10's

  • No option for diverting suppressor gas

Score: 8.0 Great

 

 

Chad's Favorite Link: Saddle Butte Machine Gun Shoot

Scalarworks LDM Micro

In continuing the effort to keep my AR-15 cleaner, meaner and leaner, I've picked up a new mount for my red dot optic. I primarily run the Vortex Sparc II, paired with the occasional 3x magnifier. Vortex pairs the Sparc II with their own mount, which comes with a flat mount, a riser mount, and a spacer convert an absolute co-witness to a lower 1/3 co-witness.

I had grown discontent with the riser mount that comes with the Sparc II from Vortex as it is a solid chunky piece that weighs 2.435oz (3.095oz with the lower 1/3 riser) and uses a single hex screw as the cross bolt for picatinny or weaver rails. After a few years of swapping and remounting I've found the risers torx screw head to start stripping and retightening is more difficult. Instead of calling Vortex for a free replacement I decided to try something lighter with a better tightening mechanism overall.

The Scalarworks Low Drag Mount is a great alternative mount for the price point. Some may scoff at buying a mount thats only $50 than the Sparc II w/ mount included, but I felt the benefits would be worth while in the long run. The thumb knob was the selling factor for me, as I've never encountered anything that finger tightened so effortlessly with a rock solid clamping mechanism.

As indecisive as I am, I like to swap optics on pretty much every picatinny rail I own. Swapping between rifles, shotguns, and even pistols, the original Vortex Sparc II riser was bulky and required a tool for removal. It did provide elevation options to the user, but based on its omission from the latest gen optic the Sparc AR, its safe to say its not the slickest solution for AR-15s and Vortex has moved forward in their design department. The fact I can now move my optic forward or back on the rail, or swapping on a different firearm entirely greatly pleases me.

I sometimes choose to run a 3x magnifier behind the Sparc II, and ease of remounting to accomodate the magnifier when flipped to the side is a huge plus. If I opt to remove the magnification and position in the sweet spot just forward of the rear backup iron sight, the adjustment is quick and tool-less. Above all, the clamp the LDM uses is very strong and so far has produced repeatable zeros for my rifles, tho specific group sizes have yet to be scientifically recorded on my end.

I prefer absolute co-witness so I can align the circles of my rear aperature, optic tube and crescented front sight hood, but sadly I will have to make do with this until I upgrade my optic to an Aimpoint.

All in all, the Scalarworks LDM is a no brainer for someone looking to upgrade their factory optic and achieve a lighter firearm. The only real negative I can point out is the co-witness height is a bit screwy when using the Sparc II. Despite having the LDM100 absolute model, my iron sights sit at the lower third position on at 15" rail. This confused me at first, causing me to return the LDM to Rainier Arms and try the lower third LDM110 model which was way too high. EDIT: Scalarworks let me know that moving forward, the LDM/Micro Absolute Model will be lowered a tad to properly cowitness with the Aimpoint T2 (and Sparc II). I'm still happy with the LDM and will continue to use it in conjunction with irons, eventhough I wish it was a perfect absolute co-witness.

FIREARMS INSIDER REVIEWS – 8 KEY POINTS

Claim to Fame: The Low Drag Mount’s precision guided telescoping clamp holds zero on every re-installation, and under the heaviest recoil. Guaranteed.

Target Market:  Aimpoint/Vortex Sparc owners

FNBs (Features & Benefits of this product):

  • Repeatable zero with each installation via precision telescoping clamp & thumb knob
  • Lightest Quick-Detach Aimpoint Micro mount in existence
  • CNC Machined from ultra high strength 7075-T6 Aluminum
  • Intuitive attachment system that won’t back out under sharp recoil
  • Adaptable to out of spec rails without additional adjustments
  • Streamlined profile free of protruding levers or knobs.
  • MATERIALS: 7075-T6 Aluminum Alloy / 4140H Steel Alloy
  • FINISHES: Mil-A-8625 Type III Hard Coat Anodizing / Black Nitride™
  • WEIGHT: 1.29oz LDM100 / 1.33oz LDM110
  • WARRANTY: Lifetime
  • HEIGHT OVER RAIL (OPTIC CENTER): 36mm (1.42″) LDM100 / 40mm (1.57″) LDM110
  •  COMPATIBLE OPTICS: Aimpoint Micro T-1, Aimpoint Micro T-2, Aimpoint Micro H-1, Aimpoint Micro H-2, Primary Arms Micro Dot, Vortex Sparc II

What other aesthetic options or finishes are available?: Absolute or Lower Third co-witness*

What others are saying?:

"The fit and finish on the LDM/Micro mount was also very nice. No sharp points or inconsistent anodizing at all. Just a very clean, high quality look. Another thing I noticed was that the anodizing seemed to match up color wise to my Aimpoint T-1 which at a quick glance makes it look like a one-piece Optic/Mount setup. The design itself I think is very attractive. So my initial impressions are very good. I am looking forward to using the LDM/Micro mount full time on my SBR this year. Pricing on the SCALARWORKS LDM/Micro mount is a bit higher than some of the other mounts on the market but I think the quality and lightweight/low drag aspect of it makes up for that very fast. One thing to note is that the LDM/Micro mount does not come with screws and requires that you use your “factory” screws. If you are like me and bought a T-1 with something other than the factory low mount you will probably need different screws. My T-1 came with the Factory LRP QD mount which has really long screws. Thankfully I had some screws from a different mount that I was able to use. This is not a problem, just something to keep in mind, when purchasing you might want to contact Aimpoint to purchase a new set of screws." www.AR15news.com

"I should point out that Scalarworks didn’t skimp on the clamping surface. The rail clamp runs the entire length of the side of the mount. Once the thumb wheel is turned to hand tight, the mount isn’t moving. I have the LDM110 which is the lower third co-witness model. I use it on a carbine that I purposely built to be extremely lightweight. At 1.37 ounces, it weighs less than half of the mount that it replaced on this build! To save that much weight on such a small part is amazing. The LDM seems to be extremely well made. The machine work is clean and the finish is even. The fit and finish on my example is excellent.  The LDM is the lightest Aimpoint Micro QD mount on the market by a wide margin. Heck, it is lighter than most non-QD mounts. It is well made, it mounts easily, it returns to zero at least as well as is required for the precision level of the optic it mounts, and it looks pretty darn good too. This is an impressive mount and I can’t wait to see how they adapt this design to support other optics. " Jerking the Trigger Review

PRICE POINT:

I need it now! Availability: Rainier Arms or Brownells

OUR RATING:

Pros:

  • Lightweight
  • Thumb Knob is knurled for grip, and employs a detent to prevent backing out
  • Clamping rail is full length
  • Compatible with multiple red dots
  • Clamping action will accomodate out-of-spec rail widths

Cons:

  • Co-witnessing a Vortex Sparc II with iron sights isn't consistent with other mounts with co-witness claims: 1mm higher than other compatible optics on AR-15s, 3mm higher on a Tavor -EDIT: Moving forward this will not be an issue as the Aimpoint T2 wasn't out yet when they made the Absolute LDM Micro. The new mounts will sit lower and achieve the proper absolute co-witness.
  • Included screws are button head and do not bite firmly with my used Sparc II, the original screws from Vortex are tapered head and are much more secure (may just be the internal threads on my optic are worn and the Scalarworks screws are a tad short with the head type.

SCORE: 8.5 GREAT

Featured FFL:

For FFL services I choose Promised Land Firearms in Toulon, IL.

Ryan's Links:

Gun & Gear Review Podcast
Hunter of Design

Hexmag Advanced Tactical Grip

  The Hexmag grip comes from the same company that brought us Hexmags. All of the Hexmag products I have seen come with a hexagonal pattern in them, thus the name. The pattern also adds a degree of flare to the looks of their products. 

  With the Advanced Tactical grip, you get this hexagonal pattern on the sides of the grip. And some raised straight lines on the front and back. But the big advantage to the Hexmag grip is its adjustability. One can choose 3 different positions or angles in which the grip sits. These are 17, 25, and 33 degrees. The setting are set up to help with different uses. The 17 degree is stated to help with AR pistols or close duty work. While the 25 degree is your standard AR grip angle. Leaving the 33 degree for a more relaxed shooting position, giving it more of a standard rifle stock feel. I found that the 25 degree position worked best for me. I guess that is why it was designed that way. 

  Now onto installation and adjustment.  The installation is very much like any AR pistol grip. Except that the Advanced Tactical grip has 2 parts. The first part holds the safety selector detent spring. It slides on as normal. Now you are left with the grip and the mounting screw. Both the grip and the mounting piece have large gear style teeth on them. Just put the screw through the handle and start tightening it as normal. Before it gets tight, position it on one of the 3 angles.  There are 3 locator lines on the back of the grip by the beavertail. These select which angle, just line them up and tighten the screw.  

  After using the grip for a while, I found it to be extremely smooth. Meaning that it was hard to get a good grip, and this was with dry hands. Hexmag sells grip tape that is cut to fit into the hexes, I would highly recommend this. I took it one step farther and stippled inside some of the hexes and also the front and rear of the grip. Besides being slick, having the option of adjustability is pretty nice. After I installed the grip, I was curious how the mounting system would hold up. Well it held up to me beating on a 2x4 with it. It didn't slip to one of the other positions, which I thought could happen. 

  If you are in the market for a new grip to enhance your AR rifle, look into the Advanced Tactical grip by Hexmag. But if you do decide to get one, get their grip tape or have it stippled. I liked the adjustability,  and now that it has been stippled, it is a nice grip

Firearms Insider Reviews - 8 Key Points

Claim to Fame:

Adjustable AR grip with cool hex pattern 

Target Market:

AR users looking for an aftermarket grip

FNBs (Features & Benefits of this product):

  • Hex pattern
  • Adjustable angles
  • Beavertail
  • Sturdy  

What other aesthetic options or finishes are available?

Black or FDE

What others are saying?:

Nice Grip 

Monte at Wise Tactical 5/5 stars

This Pistol Grip fit on my AR with no problem. It has a great feel to it and I really like that you can adjust the angle of it. It looks awesome on the Rifle, especially with the Hexmags.

Link to other reviews:

The Firearm Blog

Shooting Illustrated 

Price point:

MSRP = $27.99

Retail = $23.99 on Amazon

I need it now! Availability:

Amazon or check your local retailer

Our Rating:

Pros: 

  • Adjustable grip angle
  • Sturdy mounting system
  • Beavertail
  • Price

Cons:

  • Poor grip (slick)  
  • Has no storage inside grip

Score: 7.0 Good

 

Chad's favorite link: Saddle Butte Machine Gun shoot May 21 & 22, 2016

Fortis Rev II Handguard

Lighter handguards are becoming the new trend in AR-15 building.

Lighter handguards are becoming the new trend in AR-15 building.

AR15 handguards are about as ubiquitous as the rifle itself. Seems like more and more companies are springing up with a handguard for the dubious black rifle, and the tread seems to be lighter and more modular. With the proliferation of Keymod and MLOK rail attachment systems and less demand for full quad rail picatinny forends, the options for the end user have never been more plentiful.

The REV II's evolution brings more MLOK (or KeyMod) real estate while keeping the ounces down to a minimum.

The REV II's evolution brings more MLOK (or KeyMod) real estate while keeping the ounces down to a minimum.

I myself was interested in giving a lighter version a try, and I happened upon the Fortis REV handguards. Fortis machines some fantastic parts, and their handguards are now available in a Gen 2.0. The difference between the REV I and the REV II is the short forward rail sections in the 3, 6 & 9 o’clock positions that are present on the REV I have been removed on the REV II... and instead have been replaced with additional KeyMod/MLOK real estate and limited rotation QD sling swivel sockets.

The REV II uses the standard AR-15 barrel nut.

The REV II uses the standard AR-15 barrel nut.

The mounting collar uses four screws. 

The mounting collar uses four screws. 

I went with the 14" MLOK version of the REV II, and it is quite light. With a weight of only 9.3 ounces, Fortis really shed the excess with all of the milling and machining any of the 6061-T6 aluminum that wasn't crucial to structural integrity. The REV II uses a two part design where the main body is one solid piece, with a smaller mounting collar at the bottom rear. The REV II indexes by the two ear tabs that align on either side of the upper receiver, and a dovetail slot in the bottom that mates with the mounting collar and fastens with four screws and a 9/64 allen key.

The REV II still has the rear QD sockets for 2 point sling usage

The REV II still has the rear QD sockets for 2 point sling usage

Another design choice made to cut the fat was making the insider diameter much smaller than most other handguards on the market. At 1.340" the inside can still facilitate most low-profile gas blocks and the narrowest of suppressors like the AAC ECO-9/EVO-9 and most 22 cal cans. Be warned though, the screws/locking nuts of MLOK accessories will decrease that diameter by protruding inwards... making adding MLOK components and overlapping a can very problematic.

The narrow inside diameter of 1.34" will rule out some suppressors if you're planning on overlap, luckily the ECO/EVO 9 by AAC is 1.25" wide.

The narrow inside diameter of 1.34" will rule out some suppressors if you're planning on overlap, luckily the ECO/EVO 9 by AAC is 1.25" wide.


Overall with it's continuous top rail, anti-rotation index tabs, QD swivel sockets and use of the inexpensive and standard barrel nut, the Fortis REV II is a very nice handguard for the modern AR-15 build. The lighter weight will help keep your rifle lean and mean without sacrificing modularity

FIREARMS INSIDER REVIEWS – 8 KEY POINTS

Claim to Fame: Fortis REV™ II is an extremely lightweight yet robust free floating rail system.  When designing the REV™, we didn’t want just another rail system, we wanted a better, lighter, feature rich handguard that was robust and within budget.

Target Market:  AR15 owners

FNBs (Features & Benefits of this product):

  • Material: Aircraft Grade 6061-T6 Aluminum
  • Finish: Military Specification Type III Hard Coat Anodized
  • Length: 7", 9", 12", & 14"
  • Weight (length and rail system dependant) 12" Keymod = 7.8 Ounces
  • Inside Diameter: 1.340"
  • Continuous Top Rail
  • Rotation Limited QD Sockets
  • KEYMOD at the 3, 6, & 9 o’clock
  • Anti-Rotation Tabs
  • Uses Standard AR15 Barrel Nut (Not Included)
  • Made in the USA

What other aesthetic options or finishes are available?:  Keymod or MLOK. Some dealers offer FDE Cerakote.

What others are saying?: "I purchased a 12″ Fortis REV Free Float Rail for use on my lightweight project build and it has served me well. I needed an extremely lightweight, extended rail that mounted on the standard barrel nut for a 14.5″ barrel with permanently attached muzzle device and the REV fit hte bill perfectly. Fortis has now released the REV II that is basically the same rail except the short the 3, 6 & 9 o’clock forward rails that are present on the REV have been removed on the REV II. They have been replaced with additional KeyMod real estate and QD sling swivel sockets. The result is a rail that weighs even less at just 7.8 ounces (the REV 12 weighs in at 9.2 ounces).

This looks like an excellent revision to the REV series of rails. I really don’t use the forward rails and actually find them to be a bit uncomfortable for how I hold the carbine due to some sharp edges. The new version removes the rails, saves weight, and costs less (at the introductory price). That is a win-win-win." Jerking the Trigger Review

"I thought the cardboard tube the rail came in may have been empty b/c it was so light.  I opened up the tube...it was in there.  The rail just looks amazing imo.  I had actually called Fortis to ask about the total overall length.  I have a 12.5 barrel+was wondering how much of the barrel would be left with no rail covering it .  I had read the OAL was a bit more than 9"(it's about 9.2").  The amount of barrel left exposed on my 12.5" BCM barrel(not counting the threads on the end of the barrel) is 2.75".  I think it was the head of Fortis that answered the phone(not sure if it was).  Anyhow, I was really impressed with Fortis's customer service b/c he answered all my questions.  The rail went on SUPER EASY!!!  Being that it was my 1st upper build, that made my day.  I can't say enough good things about the rail.  I'm a very happy customer.  Also, as far as Red Barn goes, it was fast shipping, a great price, and great packaging-Couldn't ask for more!" Red Barn Armory Review

PRICE POINT:

I need it now! Availability: Rainier Arms or Red Barn Armory

OUR RATING:

Pros:

  • Lightweight
  • Easy installation around standard barrel nut
  • Continuous top rail w/ no gap

Cons:

  • Indexing tabs still not close enough to upper receive to ensure zero/level. 
  • No 7 or 9 inch MLOK versions

SCORE: 8.0 GREAT

 

Featured FFL:

For FFL services I choose Promised Land Firearms in Toulon, IL.

Ryan's Links:

Gun & Gear Review Podcast
Hunter of Design

0 Likes

 

$170.95

GunVault SpeedVault SV500

Keeping a handgun in the home can be quite the catch 22, especially if you don't live alone. You want the gun easily accessible for the unexpected "bump in the night" scenarios, but leaving it carelessly in a nightstand or sock drawer can be pretty reckless. Especially if you have curious pups or nosey house guests that could find your weapon and potentially have a negligent experience. Keeping the firearm in a traditional handgun safe "keeps people honest" as so many like to put it, but often restricts the access due to size and weight of the safe, where you keep it, and how easy it is to open when the lights are out and wasted time could endanger your life.

I myself have lived in a few apartments over the years, and frequently have friends over to visit, often with children. I've grown accustomed to have some form of defense tool within arms reach of my bed, because frankly, bad things happen. Often it would be a compact sized pistol in a handgun-rated personal safe, which is more like a lockbox. The issue with this lockbox is it takes up alot of surface space, and is obvious as hell. Unless you bolt that thing down, consider it a fun puzzle begging to be solved by anyone who isn't you. Okay so what, you just slide it under the bed, lash it to the bed frame, or just bury it in your nightstand... well good luck getting to your protection now in the middle of the night, from a dead sleep in your pitch dark room, possible with your adrenaline pumping hard enough to hear your own nerve endings pop.

The facts are homes get burglarized/broken into by criminals, and criminals tend to work late shifts. AKA sleepy time for you. So when your alarm system's siren yanks your conscious mind out of la-la land, or the sound of your window shattering just after your head hits that pillow... thats when the timer starts counting down. This could be the difference between you being another victim of a B&E, or possible assault/homicide (check the news, pull your head out of the sand, it happens). You are particularly vulnerable at night, because your cognitive and motor functions suck when you are tired or after you have just woke up. I don't care who you are. In the scenario described above, fast and foolproof is how you want accessing your defensive firearm to be, but still be secure from unauthorized hands during the rest of the day. So you want fast security. Like a quick safe, or a rapid lockbox... or a SpeedVault!

There are plenty of personal safe manufacturers in the market, but few have the recognizability and popularity of GunVault. They are most notably known for their 'No Eyes' keypads and their biometric safes these days- which would seem like straight out of a spy movie just ten years ago. The SpeedVault is no exception with both biometric and traditional keypad configurations, but it's design is what makes it one of the most unique handgun safes available today.

While most personal safes contain handguns in a horizontal format with the pistol on its side, the SpeedVault supports the firearm vertically just like a holster on the belt. This unconventional vertical format, coupled with an adaptive mounting bracket, is perfect for two main reasons: you can mount it in low profile but easy to access locations, and when unlocked the gun's grip is exposed for a fast and unhindered grip. Just about the only thing it doesn't do is call 911 for you... but when seconds count and law enforcement is minutes away, you've at least got a gun in your hands!

The mounting bracket is ambidextrous, meaning you can mount it to either the left or right side of an object.

The mounting bracket is ambidextrous, meaning you can mount it to either the left or right side of an object.

First you line up the tabs with the safe's slots

First you line up the tabs with the safe's slots

Next thread the three thumbscrews into the bracket. The holes should be properly indexed when the hooks are in the mounting slots.

Next thread the three thumbscrews into the bracket. The holes should be properly indexed when the hooks are in the mounting slots.

Right out of the box, you could probably have the SV500 mounted, programed and fully operational in 20 minutes or less. That is, unless you have to run to the gas station because you don't have a spare 9 volt battery handy, and you glanced over the line on the package that said battery not included. While the included wood screws are kinda short, they allow you to mount the bracket right to the inside of a desk, headboard, nightstand, cupboard etc. without unnecessarily over-penetrating your furniture, or pinning your drawers shut accidentally. If you wish to mount into drywall or cinderblocks, I would suggest a trip to the hardware store because these screws are only good for wood.

The safe itself screws into the mounting bracket internally, which means I had to bust out the manual and read the instructions. You have to unlock the safe using either the key or the factory-programed code, remove the hinged door itself so you have enough room to insert screws from the inside and hand tighten against the mounting bracket. This may be a difficult task for large-mitted individuals so pliers may be needed. When the three screws are fastened, the safe itself conceals the screws holding the bracket to your surface of choice.

After a bathroom break and a victory beverage, the safe is ready for locking up your pistol, or reprogrammed to a code of your liking. Obviously with the biometric model SVB-500 you would scan in your fingerprints, as well as your spouse or any other authorized users. I chose the get the keypad version SV-500 because a.) it was cheaper and b.) I felt a manually entered sequence was less prone to fault than a biometric reader. OR rather, if a code didn't work, I would be to blame, not the SpeedVault. Entering my personal code is something I could train for and develop muscle memory.  Also if my fingers are ever injured or covered in blood, dirt, oil, Cheeto dust, etc. the keypad would still function.

The SpeedVault has a floorplate that secures the door to its hinge. You have to partially install the door inside the safe so the hooks go over the hinge bar, then you screw in the bottom plate to complete the installation.

The SpeedVault has a floorplate that secures the door to its hinge. You have to partially install the door inside the safe so the hooks go over the hinge bar, then you screw in the bottom plate to complete the installation.

What's really interesting is you have the option to program simultaneous button presses into your code sequence. So instead of 1,2,3,4,5,6 you could program 1,2-2,3,4-4-4,5,6 or any combination in between. Even though there are only four buttons, you are allowed a code between 3-6 keystrokes long. I like the idea of throwing a double press in the sequence because its not something a prying individual would typically try, and it increases the difficulty of it being figured out. Just be forewarned, the two/three combo finger presses have to be simultaneous, and the window for error is small.

If you miss or are slow with the other finger slightly, the entry will be incorrect.

Now keep in mind the safe will enter a "sleep mode" and lockout the keypad for 2 minutes if the correct code isn't entered within 24 key presses, and any additional attempts during that 2 minute period will makes the safe beep three times and the LED flash a red light. 2 minute "timeouts" between mischievous attempts should be long enough for a child to lose interest, and the tamper indicator feature allows you to see if someone attempted to open the safe since the last successful code was entered.

The SV-500 fits the entire full-size 1911 with no issue, and I can get my fingers around the frame to pull out.

One of the most popular complaints with digital keypads on a safe is the audible beep with each button press, and/or when successfully opened. The SpeedVault will beep like this from the factory, but it is very easy to disable the tones using the internal switch. Honestly it was the first thing I did when I got the SV-500 open, if I wanted it hear a beep every time I pushed a button I would just play with the microwave. An inward-facing internal bulb illuminates the gun when the safe is opened day or night, which I find useful and not intense enough to ruin my dilated pupils and kill my night vision. Its just enough to see where you are reaching if need be.

The inside is very simple, batter compartment, and two buttons: Learn (program) and Mute (no more beeps)

The inside is very simple, batter compartment, and two buttons: Learn (program) and Mute (no more beeps)

The biggest complaint about the SV-500 is the sound of the electronically powered mechanism inside winding up, followed by the "thunk" sound of the door becoming freed from the lock. Yes the hinged door does make another sound when gravity drops it to its fully opened position and contacts the stop, but this is not where the most audible of the sounds originate. Even when guiding the door open with your hand, the unlocking mechanism is the unwelcome noise. While I wouldn't call it entirely audible from the hallway outside the bedroom door (I've tested it) it is audible enough within the room. So if you plan to stash a candy bar in it for late night snack time, your partner will probably hear it and have some choice words.

Note: If you are a wheel-gunner through and through, barrels longer than 4 inches will bottom out and not fully support the firearm in the foam pocket. This causes the gun to droop and the grip to protrude from the door.

Internally, the 'holster' part of the safe is comprised of a foam pocket. This rectangular pocket is meant to hold your gun's slide, exposing the frame and grip for easy extraction. The depth of this pocket can facilitate a full-size 5" 1911, but anything larger I would have my doubts (a Desert Eagle would probably be incompatible). Obviously something in the compact range is ideal too, with room for an extra magazine if its small enough. The pocket isn't cut that large, but it is only foam so it nicely stretches and conforms around the slide and the light correctly.

I was surprised to find my S&W M&P357c fit even with a Streamlight TLR-3 light

All in all, the SpeedVault is fantastic. Not only can you mount it beside your bed or even under your desk at the office (where allowed) but the speed at which you can withdraw your handgun is exceptional. The only negatives I can think of are the noisy unlocking mechanism and the finicky double or triple code presses. I've also tried a larger gun and light combo for fit, the Glock 17 with Streamlight TLR-1 checks out. I keep my gun in condition 1 inside the SV-500, meaning a round chambered, full magazine in place and hammer cocked (or in my case, striker). Whether or not you leave the safety engaged is your preference, I'm used to carrying without a safety so my M&P is ready to go as soon as its in my hand.

FIREARMS INSIDER REVIEWS – 8 KEY POINTS

Claim to Fame: Keep your handgun safe, secure and ready for action with the SpeedVault. Offering a revolutionary design, the SpeedVault is equally as fast as it is discreet. It is the ideal choice for a home or business looking for added security

Target Market:  Those seeking basic gun security w/ quick access in the home or office

FNBs (Features & Benefits of this product):

  • Digital Keypad (biometric version also available)
  • Multiple mounting options
  • 18-gauge steel construction
  • Tamper resistant door
  • Backup override key included
  • Audio and LED low battery warning
  • Foam lined interior
  • Weight 6.61 lbs
  • Outer Dimensions 13"L x 3.5"W x 6.5"H

What other aesthetic options or finishes are available?: Black Only, but biometric access available in SVB-500 model.

What others are saying?: " 4/5 Stars - Works great, easy to install (I watched a video on YouTube) and I would recommend to anyone wanting immediate access to their weapon by their bedside, and also for safety reasons as children cannot gain access without the code or key. Also great to have the keys as backup in case our memory goes away (with age) and we forget the code. :-) Only concern is light does come on when it opens and there's a pretty audible "clunk" when the drawer drops." Sportsmans Warehouse User Review

" This is not a safe against determined intruders, nor is it a fire safe. It is a safe that will stop kids and honest adults from getting the gun while keeping it ready to use if needed. If you want a serious gun safe, then don't buy this and then complain that it is thin metal (but not flimsy by any measure). After installing it (with the short screws on solid wood) I can say that it would take a heck of a blow from a sledge hammer to knock it loose, or a determined assault from a crow bar, but again, it is not designed to stop a determined attack. Finally, if you are concerned about the people saying it is too loud, or the light is too bright, here's a reality check. As much as I like to imagine myself as Liam Neeson going rogue and blasting my daughter free from sex traffickers, this is not the case. This is not a product for black ops agents, it is a product for responsible gun owners with families. If we have to draw a gun against a person to defend ourselves in our homes, a light or a whirring is the least of our problems. It is a great product and the price is right." Amazon User Review

PRICE POINT:

I need it now! Availability: Brownells, Amazon or many sporting goods stores

OUR RATING:

Pros:

  • Very simple to program
  • Large buttons easy to use without vision
  • Keypad sequence can contain combinations of 2-3 buttons simultaneously pressed
  • Bright white internal light illuminates contents
  • Audible beep when buttons pressed is easily muted/turned off
  • Flexibility in mounting options (left or right side, desks, nightstands, etc.)
  • Easy programming + physical key backup
  • Steel construction feels extremely solid
  • Internal foam lined 'pocket' holds various gun models/sizes, even with light or laser accessories

Cons:

  • Very audible mechanical whining and "clunk" noise as the electronic latch locks/unlocks
  • Mounting bracket lacks screw hole options for wall stud
  • Included mounting screws are short
  • Double or triple press codes are finicky and can cause incorrect entries
  • Low battery warning only when keypad pressed

SCORE: 8.5 GREAT

 

Featured FFL:

For FFL services I choose Promised Land Firearms in Toulon, IL.

Ryan's Links:

Gun & Gear Review Podcast
Hunter of Design

Axelson Tactical TALON muzzle brake

  The AxeTac TALON muzzle brake is made by Axelson Tactical out of Nevada. If you recognize the name it might be because the company was started by the brother of Matt "Axe" Axelson of Lone Survivor Fame.  They have brought out a number of products for AR-15 type rifles, along with their AXE series complete rifles.

  I have put quit a few rounds through the TALON brake they sent me. I also have shot a couple of the AXE rifles with them installed. The brake does an excellent job of reducing felt recoil, not that a 5.56 AR has much recoil. But what I was most impressed with was its ability to keep muzzle rise to almost nothing. It was easy to get accurate double taps, shooting off hand, at a 24" steel target at 200yds. This was with a 16" barrel and a red dot optic.

  The AxeTac TALON is sold as a muzzle brake, but it really is more. It is noticeably louder than a standard A2 flash hider, but not as loud as my 3 port comps that direct the blast out the sides. The TALON also does a great job as a flash hider, keeping the flash contained within it. And as a compensator it also does an excellent job. It will still allow some of the blast to go forward, but it doesn't seem to hurt its effectiveness as a comp. I ran the TALON on a 16" and an 11.5" AR. Yes, it worked better on the 16", but it worked quite well on the 11.5" also.

  Now onto the technical stuff. The TALON has 3 small slots, 1 facing up, and the other 2 facing the sides but slightly lower than 90 degrees. It also 2 large ports between the small slots. And 3 open ports at the end spaced evenly. The bottom is mainly closed except for the port at the end of the muzzle. Also on the bottom is the Axelson Tactical logo. The brake is 0.940" in diameter, and 2.5" long, not counting the crush washer (which is included). There are also flats to fit your standard muzzle device tools or a 3/4" wrench. It is made from stainless steel, heat treated, and then black Melonite coated. It is threaded the standard 1/2"-28.

  I would not hesitate to install one of these on another rifle. The finish is excellent. It does a good job at being a comp, brake, and flash hider. It's made in the USA. If you are looking for a good all around muzzle device, check into the Axelson Tactical TALON muzzle brake.

Firearms Insider Reviews - 8 Key Points

Claim to Fame:

AR-15 Muzzle Brake, Compensator, and Flash Hider all in one.

Target Market:

Shooters looking to mitigate recoil.

FNBs (Features & Benefits of this product):

  • Reduces felt recoil

  • Reduces muzzle rise

  • Reduces flash

  • Made from stainless steel

  • Melonite coated

What other aesthetic options or finishes are available?

None

Link to other reviews:

Google was not my friend and I could not locate any

Price point:

MSRP = $94.99

Retail = $94.99 on Amazon

I need it now! Availability:

Axleson Tactical or Amazon

Our Rating:

Pros:

  • Reduced recoil

  • Almost no muzzle rise

  • Melonite coated

  • Stainless Steel

  • Made in USA

  • Includes crush washer

Cons:

  • Price

  • Longer than a standard birdcage flash hider

85.jpg

Score: 8.5 Great

 

 


Chad's Favorite: Patriot Patch Co.

SEARCH