Chad Wallace

March 4, 2023

review

Streamlight ProTac 2.0 Weaponlight

Chad Wallace

March 4, 2023

review

When it comes to weapon lights, there are plenty on the market. The new Streamlight ProTac 2.0 Weaponlight is one of them. This Streamlight 2.0 falls somewhere between those cheap Amazon lights and the super expensive “pro” lights. Don’t underestimate the ProTac 2.0, it has some really nice features. As of right now, it is only available in a kit with a pressure switch.

If you are in the market for a weaponlight, there are a few things to take into consideration. The first is probably lumens. Everyone has a lumen rating for their light and it’s usually advertised highly. But remember that lumens don’t tell the whole story about lighting, there is also candela. In simple terms, lumens measure total brightness and candela measures how that brightness is applied. The Streamlight Protac 2.0 has a max brightness of 2000 lumens and a candela rating of 17,700. In the case of the ProTac 2.0 you get a bright output but a wider beam pattern. The higher the candela rating, the more focused the beam is, or how much farther the light will project. Streamlight rated the beam distance at 266 meters for the 2.0. In comparison, Streamlight’s HL-X has half the lumens of the ProTac 2.0, but a candela of 27k for a beam distance of 332 meters. A higher candela rating will also help the light push through photonic barriers, like smoke or fog, better. The ProTac 2.0’s beam is really good for buildings and rooms where there isn’t a need for target identification at 200 yds. It would make a good light for your home defense rifle or shotgun.

Target backers at 50 & 100 yds, barely visible are 200 yd backers

The ProTac 2.0 Weaponlight has some other impressive attributes. It’s not incredibly long at 6.3 inches, or heavy at just over 9 ounces. It comes standard with a picatinny mount. If you don’t like the picatinny mount, the Protac 2.0 uses a standard “scout” mounting platform. This makes MLok mounts and the like fairly easy to come by. I installed a 45 degree MLok mount on it since I didn’t like how far off the rail the picatinny mount mounted the light. The ProTac 2.0 also comes with a pressure pad. This is only a pressure pad with no switch on it. New for Streamlight is the way the pressure switch attaches to the light. There is a dual end cap. The end cap has a switch, but also has an outlet to plug in the pressure pad. This way one can use the switch and the pressure pad. Before, you were limited to one or the other. I must say, this dual end cap setup is pretty nice. If not using the port, an attached plug can be used to keep it protected.

The Streamlight ProTac 2.0 is rechargeable. There is no option to use off the shelf batteries if needed. The battery used is also proprietary. Extra batteries run around $30. There are, however, some different ways to charge the battery. On the body of the light, there is a sliding cover over the battery's charging port. Just slide it down from the lights head and plug in your charging cord. The cover slides over an o-ring to protect it from water and dirt. The cover never opened up by itself, so that's a plus. The other way is to take the battery out and plug the charging cord into it directly. This new battery gives the ProTac 2.0 a 2.5 hour runtime on high or 11 hours on low.

Streamlight is known for their ability to program the lights function. The ProTac 2.0 is no different. It still uses their “Ten-Tap” programming. Press the button 10 times fast, holding it down on the 10th “tap”. Once the light goes out, release the button. Now you are in the next mode. Do this until the mode you want is selected. The ProTac 2.0 has 3 programming options. They are: High/Strobe, High only, and Low/High. I have it set to high only, but choose what works best for you. Low output is 250 lumens. Strobe and high are 2000 lumens.

I really enjoyed how the ProTac 2.0 functioned. The pressure pad, along with the included mounting hardware, worked great. Since the pad doesn’t have an on/off switch, I use my thumb on the tailcap switch. That way if I need it to be always on, I just push the button. Having that ability, with the new dual tailcap, is really nice. The light output is bright enough to light up my entire living room or bedroom. I can’t identify targets very well at over 100yds, but they can still be seen just fine. I just can’t see if they have a weapon or not. I immediately changed out the picatinny mount because it put the light too far away from the rail, so it was awkward to reach the tailcap button. Having the standard “scout” mounting platform made that an easy fix.

The Streamlight ProTac 2.0 Weaponlight kit is a good all around light. Especially if you don’t mind proprietary batteries. If it’s your first weaponlight, then those batteries won’t matter as much. The light is programmable and bright. The new tailcap makes the light more useful too. At a price of around $170, the Protac 2.0 is something to look at.

Firearms Insider Reviews - 8 Key Points

Claim to Fame:

2000 Lumen weapon mounted light kit

Target Market:

Those needing or wanting a weapon mounted light

FNBs (Features & Benefits of this product):

Uses one (1) Streamlight SL-B50® protected Li-Ion USB-rechargeable battery pack (included)
Features TEN-TAP® programming - Choice of three user selectable programs:
1) high/strobe 2) high only 3) low/high
High: 2,000 lumens; 266 m beam; runs 2.5 hours
Low: 250 lumens; 93 m beam; runs 11 hours
Strobe for signaling or disorienting: runs 4.5 hours
IP67-rated; dust-tight and waterproof to 1 meter for 30 minutes (IPX4-rated when remote switch is plugged in)
2-meter impact resistance tested
6000 series machined aircraft aluminum with Type II MIL-Spec anodized finish
Mounts directly to guns with MIL-STD-1913 (Picatinny) rails
Includes remote pressure switch
6.30 in (16.0 cm)
9.06 oz (257 g) with one (1) SL-B50® battery pack
Limited Lifetime Warranty

Our Rating:

Pros:

Hi Lumens for lots of light spill
Dual connection battery cap
On weapon charging
Decent pressure switch

Cons:

Proprietary battery
Low Candela
Only comes with 1 battery
Picatinny mount

Score: 7.00 Good

Favorite Link: Atibal Optics

Chad Wallace

February 23, 2023

Review

Strike Industries Dual Folding Adapter

Chad Wallace

February 23, 2023

Review

Strike Industries recently brought out their Dual Folding Adapter. It is a unique folding stock, or brace, for mounting on a picatinny rail, hence the “adapter” part of the name. From pistols to rifles, the Dual Folding Adapter (DFA) has a variety of uses.

The Dual Folding Adapter comes with everything needed for multiple mounting options. It comes in the box set up to be used as a pistol brace. Also in the box is a buttplate. The buttplate is to use the DFA on a rifle or registered Short Barrel Rifle (SBR). Do not put the buttplate on the DFA while it’s on a pistol. The buttplate also has a rubber buttpad attached to it. To mount the DFA to anything, you need a firearm with a rear vertical picatinny rail. Then you just slide it on the pic rail, insert the screws, and tighten it down. The stabilizer has a QD socket at the top rear, for use with a single point sling. This lets you put pressure against the sling, to help stabilize the pistol. The buttplate is pretty explanatory for a rifle. The buttplate also has 2 QD’s, one on either side, for mounting a sling. To switch between the buttplate and the stabilizer, there is a torx head screw that goes through the end of either one of them, and screws into the strut.

Now for the best part. The Strike Industries Dual Folding Adapter folds both ways! There are 2 buttons on the top, by the picatinny rail mount. These buttons unlock the DFA so it can fold. If looking at it like you hold a pistol or rifle, push the left button down, into its recess, and the DFA can then be folded to the right. Or, push the right button and it can be folded to the left. The DFA has a slight 3 degree downward angle, when folded. This is to help clear ejection ports, so that a rifle can still be fired with the DFA folded. To unfold the DFA, you have to push up slightly and then pivot the DFA out to lock it in the unfolded position. If you push up by the stabilizer or buttplate, nothing happens. You have to push up closer to the hinged portion, or the DFA won’t unfold. I like how this worked because you aren’t accidentally unfolding the DFA. It is also really easy and quick to unfold the DFA. Just push up a little with your thumb and you are in business. There is a small price to pay for the ability to fold both directions. That comes in the way of the picatinny rail mount and folding mechanism. The folding mechanism is 2” wide, so it is the widest part on the whole DFA. One typically mounts the DFA up by the firearms receiver, so it’s not as bad as it sounds.

Other than the folding point, the Dual Folding Adapter is quite slim. The strut on the DFA extends rearward from the folding mechanism, it has some lightening cuts and is only about ½” wide. The whole DFA weighs under 10 ounces, so it’s not heavy at all. Total length on the DFA is about 9.25”. In the folded position it adds, a tiny bit over, an inch to your firearm. If, for some reason, you want to take the DFA off, you can push both the buttons and slide it off of the picatinny mount. Why, I am not sure, because it folds. Strike Industries also sent me out their Cheek Riser. This is for using the DFA as a rifle stock. The cheek riser clamps on through 2 holes in the strut. It has 3 height positions. The cheek riser makes the strut much more comfortable to lay your cheek against. Plus those height adjustments let you get your eye in the right spot for your optics. I was impressed with how comfortable and useful this little piece of polymer was.

The Dual Folding Adapter was used mainly on a Strike Modular Chassis. So it was used in the pistol stabilizer configuration. I was pleasantly surprised at how well the DFA stabilizer brace worked for me. It rested nicely against my arm and really did help stabilize the pistol. There is a tiny bit of up down movement in the whole system, but it’s less than some M4 stocks, so no complaints about stability. Speaking of stability, Strike Industries has little rubber bumpers that go inside the DFA to help with lockup and cushion the impact of that lockup. I ended up using the thickest ones provided, as they gave the best feel and tightness. I probably have opened and closed the DFA more than I should have. It’s kind of a fidget spinner for firearms.

If you happen to be in the market for a folding stock or brace, why not let it fold both ways. The Strike Industries Dual Folding Adapter does just that. It makes an excellent stock, as it is sturdy, and it really shines as a foldable brace. Strike Industries has really stepped up their accessory game in the last few years, The Dual Folding Adapter is definitely one to check out.