Holsters

Werkz M2 holster for Polymer80

 Werkz holsters is a small kydex company located in Princeton Idaho. I first heard of them on the Handgun Radio podcast. Werkz makes of variety of formed holsters and accessories. From custom to off the shelf, they have you covered. Werkz sent me one of their M2 IWB holsters for a Polymer 80 PF940c and a M2 magazine carrier for this review.

 The M2 holster is a taco style design with some other features. A taco style holster is one that is made out of one piece of material, then folded over a mold, hence the taco name. A feature that I didn’t think I would use was the ability to convert it to an outside the waistband (OWB) holster. I found this actually quit useful when I realized that this was the only holster I had for my Polymer 80 and needed it OWB. I switched the clip to the other side. To do this, one just removes the two screws holding the clip on, and moves it to the other side. The M2 has clip locations at two heights and an angled location also. I ran the holster IWB with it angled or canted forward. This resulted in the main dislike of the holster. The clip doesn’t completely rest against the holster. It hangs about halfway off. When wearing it in this config, I felt as if it didn’t have as much surface area holding onto my belt and was also easier to take the holster off of the belt. When using the M2 in the straight upright position, this was not a factor.

 I must admit, this is one of the nicest finished holsters I have used. The edges are smooth, and I mean real smooth. It has some sort of texture on the outside. The Werkz logo is etched or laser engraved into the kydex. There are bosses where the clip is screwed on. It is open at the bottom so that a longer, or threaded barrel, will fit. The sight channel is really tall to clear suppressor height sights. It is even clearanced for a micro red dot sight.

 I’ve worn the M2 on and off since receiving it. It holds the pistol very nicely with good retention. One can adjust the retention somewhat by tightening or loosening the tension screws. The M2 does seem to print some under a T-shirt, or any thinner shirt. That is why I only wore it off and on. If I had a jacket on, no problem, but I usually just wear a T-shirt as a cover garment. I mainly wore it at the 2:30 to 3 o’clock position. Angling the pistol/holster combo forward didn’t seem to make it print any less. After about 3 days of wearing the M2, my body adjusted and it was comfortable, at least somewhat. I like how the M2 only has one wide clip, it makes it easier to locate exactly where it is the most comfortable. The M2 is a small holster, Werkz even calls it minimalist, and I’d have to agree.

 As I also mentioned, I wore the M2 as an OWB holster also. This is also when I mainly used the M2 mag carrier. I wore the M2 at a local Steel Challenge match. I was concerned using it with just the single clip. After 25 draws and reholsters, I am no longer concerned at all. It performed well as an OWB rig.

 Now a little about the M2 magazine carrier. The mag carrier is also a taco style and holds the magazine vertically. It is currently only offered for 9mm/40 Glock style magazines. As with the holster, the mag carrier clip is also reversible for IWB/OWB. I never reversed the clip, I just turned the magazine around and it worked fine. The M2 mag carrier is of the same high quality as the M2 holster.

 If you are looking for a good quality, and inexpensive holster, give Werkz a look. If the M2 is in stock, it is one of the “quick ship” holsters. So you can have it quickly also. They will also do custom holsters, if that’s what you’re looking for.

Firearms Insider Reviews - 8 Key Points

Claim to Fame:

Minimalist Kydex Holster

Target Market:

Those needing a decent holster

FNBs (Features & Benefits of this product):

  • IWB - OWB convertible

  • Kydex

  • Adjustable clip height

  • 1.5” belt clip

  • Straight or canted

  • Adjustable retention

  • Useable with slide mounted optics

What other aesthetic options or finishes are available?

With or Without some rail mounted lights and colors

What others are saying?:

One holster to do it all. 5/5 stars on Amazon
By Dan S
Awesome holster. Ambidextrous carry options for every situation and adjustable retention. So far this is the only holster I could find that can AWIB and strong side OWB carry without replacing any parts, just moving some screws and bushings. Comfortable and has minimal printing. Also, you can't beat this price. Nearest comparable product from a reputable source is going to cost more for less features.

Link to other reviews:

None for this particular holster

Price point:

MSRP holster = $42.50

MSRP mag carrier = $30.00

Retail = $50.00 on Amazon

I need it now! Availability:

Werkz or Amazon

Our Rating:

Pros:

  • Great construction

  • Adjustable retention

  • Adjustable cant

  • Convertible between IWB and OWB

  • Price

Cons:

  • Holster prints

  • Clip

Score: 7.5 Good

75.jpg

 

Favorite Link:   Triggrcon




 

Werkz M2 w/TLR-1 Holster

Written by: Zane Mungillo

     Finding a good holster can be hard.  It’s such a personally dependent thing. There is a reason I have two large drawers full of them.  What is a great choice for me may be entirely wrong for you. It’s for that reason I approach holster reviews a little differently than other products. All holsters, in my opinion, should have the following qualities to even be considered for concealed carry:
•completely cover the trigger/guard
•allow for a full firing “master” grip on the gun while holstered
• have positive retention of some kind
•be made of either leather or kydex (not both) 
•allow for one handed reholstering. 
•firmly attach to the belt or pants
    
 Had the Werkz not “passed” these requirements, I would not have continued the review. 

     The Werkz holster took me on an emotional roller coaster if you will. A variation on their m2 iwb (customized for my gun and light) the holster, at first glance, appears to be very well crafted. All edges were buffed and perfectly smooth. It’s comes with a 1.5” injection molded clip that can be mounted at two different ride heights, straight draw or canted forward or backwards. It also has two tension screws for adjusting how much passive retention is on the gun/light combo. Retention is good when set to my preferred stiffness and a solid audible and tactile click is present when the gun is inserted, I knew I was going to love this holster. 

     That is, until I put it on, while extremely comfortable I couldn’t conceal the gun. The grip printed horribly in my typical dress, shorts and a t-shirt. Standing a boring 5’10” and weighing in at around 150 lbs I realize that I’m asking a lot of a holster to conceal a g17 in my extra medium t-shirts.  To give the holster a fair shake, I wore a slightly larger shirt a few days a week and carried around the house and at the range where I’m much less concerned with printing. 

     After about 2 months, when taking the gun and holster off I noticed the two tension screws had completely backed out and where nowhere to be found. The gun still had plenty of retention while in the waistband but this was concerning to me. To be fair I didn’t apply loctite after setting the desired retention so I chalk this up to that.  Since I used to make holsters in my shed, I have plenty of Chicago screws and such laying around so I replaced them and applied loctite this time (like I should have as soon as I got the holster).

     I decided to “modify” the holster at this point to make it more concealable so I superglued a pair of Dr. Scholls pads  to the inside portion and glue a furniture slide pad to the front inline with the belt clip. This both tilted the grip into my stomach but rotated the grip around. Werkz now offers a claw to accomplish the rotation of the grip and a quick google search of “the aiwb holster hack, Limatunes” will show you how to do the Dr. Scholls hack. I in no way removed material or heated the holster as to compromise the function of it. I simply added a wedge and a claw. 

     The holster now works fine with my typical dress and I’m very pleased with it.  I have over a thousand drawstrokes from it over the course of much dryfire and many range trips as well as about six months worth of  carry. I’m carrying it everyday for now until the next new hotness comes around that I have to try. 

FIREARMS INSIDER REVIEWS - 8 KEY POINTS

CLAIM TO FAME:  

Holsters made with little extra bulk and fast turnaround time, even on custom orders

TARGET MARKET:  

Concealed carriers 

FNBS (FEATURES & BENEFITS OF THIS PRODUCT):  

  • Meets my requirements for a good holster
  • Well made

WHAT OTHER AESTHETIC OPTIONS OR FINISHES ARE AVAILABLE?

Black, Blue, coyote brown, dark gray, FDE, olive drab, carbon fiber black, carbon fiber blood red, carbon fiber coyote, carbon fiber fde. 
Firearm and light options
1.5” or 1.75” clip 

What others are saying:  

Couldn’t find anything for this particular setup (g17w/trl-1) 
The only other reviews I found were on amazon and they tend to be hit or miss. 

Price point:  

MSRP - $42-80 depending model and options.

Retail - Same

I need it now availability: 

Werkz.com - Ships next day on in stock, 2-5 days for quick ship customs and 10 business days on completely custom orders.

Our Ratings:

Pros: 

  • Works as advertised
  • Holds gun securely


Cons: 

  • Not as concealable as other holsters I’ve tried 


Score: 7.50 Good

6.5 before modifying 8.5 after for an average or 7.5

75.jpg

Raven Concealment Eidolon

Written by: Zane M.

Selecting a holster can be a daunting task. Anyone who is serious about carrying a firearm probably has at least one box or drawer full of holsters that have fallen short in one way or another. I have two and half dresser drawers full of bad ideas and borderline junk myself.

  About a year ago I decided to try the  appendix inside the waistband(AIWB) position for various reasons. After trying a few holsters that I found and a few I made without much success, I reached out to some friends in the industry for suggestions.

  Highly recommended was the raven concealment systems eidolon. One of my friends had one he wasn’t using anymore so he sent it my way for some testing and evaluation. If you’re not familiar with the eidolon it is extremely user configurable. So much so it can be intimidating but it’s comes with a user’s manual and I recommend you read it.

  I kept the holster in the configuration it came to me in: a single belt strut(molded clip) and the RCS claw. Both soft loops and over struts can be used. Typically I’m a fan of soft loops but I have nothing against struts so I chose to keep it as configured. Other options include a wedge for pushing the top of the gun into your body, the claw(that I did use) for rotating the grip towards your body and wings so the holster can be configured for hip carry. The holster can be used right handed or left handed by simply switching out the mounting hardware. The holster is available for a wide array of guns as long as it’s a small frame glock that is to say double stack 9mm/.40/.357sig/.45gap (people use .45gap?) the model I have is cut to glock19 length with an open bottom. The majority of the testing was done with a glock 17, I also used it with a glock 26 for  comparison sake.

  At this point it’s worth mentioning I stand a staggering 5’10” tall and am weighting in at a whopping 150lbs, in other words, I’m not a big dude. The holster is comfortable and extremely good at concealing the gun. It covers the trigger completely but still allows for a full firing grip while the gun is holstered, even with a custom undercut on the trigger guard.  The strut is well made and after several hundred draws never once did it slip off the belt. As I was using a g17 there was about a half of an inch of slide sticking out the bottom of the holster, however I didn’t find this to be a problem. RCS offers a version with a closed bottom for the g17 size guns if that’s an issue for you. The gun stays in place, even with only one belt strut, and the rcs claw really does wonders for rotating the grip into the body making concealment of a full size gun not only possible but easy.   With the g26 the gun literally disappears.) If I were to continue to use the holster for every day use I would probably add a 2nd strut or even use two tuckable soft loops (available with the full kit or from RCS) I did add a strip of Velcro to put a foam wedge on, even though RCS offers a wedge I chose this route for the simple reason that I had the wedge already for another holster. A g26 in the eidolon is my go to non permissive environment rig (all federal, state and local laws followed of course) but no longer use it for the g17. The only reason for this is I now carry a weapon mount light and this holster doesn’t allow for that.

  If you’re looking for a user configurable, AIWB holster for your glock, you should take a good look at the RCS eidolon.

Firearms Insider Reviews - 8 Key Points

Claim to Fame:

A comfortable user configurable  AIWB holster for compact and full size glocks.

Target Market:

Anyone with a need to conceal a 19/17 size glock. Concealed carriers, off duty law enforcement and special operators with the military/security forces

FNBs (Features & Benefits of this product):

  • RCS claw and wedge

  • Completely covers the trigger but still allows for a full firing grip even with an undercut.  

  •  User configurable   

  •  Injection molded

What other aesthetic options or finishes are available?

Black or Limited clear at time of writing

What others are saying?:

From raven concealment systems website

“I ordered the G17 Full Kit for my G19 MOS w/ Trijicon RMR. It's a solid product! Shipping was fast and craftsmanship is top notch. My favorite holster to this day. I went ahead and ordered the soft loops too.”

Amazon review

“Ok like most everyone else I've been trying to make the switch to appendix carry. Finally after 6 different holsters I am appendix carrying. This holster is comfortable and most importantly it doesn't print. It literally disappears. I will say I bought the clips and they didn't work. I had to order the soft loops to make it work. I could never get the clips in the "right" position. Save yourself some money and buy the soft loops from the start. I paid $25 to order the soft loops after the fact when I could have gotten them for less than $10 by just ordering them with the holster. At the end of the day I can now carry off duty in the appendix position comfortably.”

Link to other reviews:

Breach Bang Clear

Price point:

MSRP = $59.99-149.99

Retail = $54.24 on Amazon

I need it now! Availability:

Raven Concealment and Amazon

Our Rating:

Pros:

  • user configurable

  • Super comfortable

  • Very well made

  • Cut for use with RMR/RDS

  • Tall sight channel

  • Mag release guard/ but not covered

  • Tuckable

Cons:

  • Only for glocks

Score: 9.0 Amazing

90.jpg

RPS Tactical Adaptive Holster Review

Everyone has been there; the drawer or tupperware container full of holsters. You’ve tried numerous ones, and there is always some sort of issue with them. The holster is too bulky; the holster doesn’t have any flex to work with your body shape; it only allows for one method of carry or storage. RPS Tactical has addressed these issues. Located in Fairfield, Maine, RPS Tactical was started by a local LEO and his brother, with a focus on making holsters, belts & nylon gear along with many other custom items. I spent some time with Rob and his brother Nick and discussed the way they make their holsters, as well as the way they hand stitch their belts. Their attention to detail and commitment to quality is very apparent in the way they make their items and the final product they put out. They are also willing to work with the customer. When I wanted to get a holster made by them, they didn’t have the mold for my Steyr C9A1 (most people don’t) and they were willing to let me bring my firearm over for them to mold the holster. I know another individual who had a specific need and they worked with him to get the holster and belt exactly as he wanted it. With the owner of RPS Tactical being a law enforcement officer, they have a really good understanding of what goes into comfortable everyday carry of firearms and other gear.

I did a podcast with the guys at RPS and they made me the Adaptive Holster for my Steyr for me to evaluate. I spent almost 8 months carrying my Steyr with the Adaptive holster in the IWB and then the OWB configurations. I had long road trips in the car, range trips, working outside, going on walks with my wife and son & pretty much every single other everyday thing you do. The Adaptive holster is a kydex shell with a sturdy leather  backing. On the body side of the backing material is the soft side of industrial strength velcro. This allows for various mounting options if you purchase the corresponding velcro patches that can be affixed to any surface. For my body type, I found the OWB configuration worked better for me. I carried setup as IWB from June to about November, when I switched to the OWB configuration as the weather got colder and I could start wearing jackets. The IWB worked good, but with my body type I’ve found that IWB can be uncomfortable over extended periods of time. I am confident other people that don’t have issues with IWB carry will find the RPS Tactical Adaptive holster very comfortable.

 

During my time wearing the holster (and I am still wearing it to this day) i noticed no abnormal wear or any hardware backing out or failing on it. Everything was very sturdy, reholstering was very easily accomplished, and the trigger guard was suitably covered. The kydex is molded to your specific firearm, and the retention was fantastic.  As with most high quality holsters, the leather backing was cut to allow for a full grip on the firearm prior to drawing.

One thing I will also note is the soft side velcro backing. While it is there for the mounting options as we discussed before, it also makes for very comfortable carry if the holster is directly against your skin. I, like many people, do not enjoy having a tucked in shirt. I have used other holsters that have the large leather backing and oftentimes found that when they were against bare skin that there was a lot of perspiration and discomfort especially in the hot summer months. It seems like the soft velcro backing on the body side of the holster allows some air to get in between the backing and your skin, preventing any perspiration or discomfort from occurring. For those of you who like to wear a tucked in shirt, the IWB configuration is tuckable as well. There are other carry options for the adaptive holster as well, including a paddle mount or  purchasing the RPS Tactical Shoulder harness and using your existing holster as a shoulder holster.

If you are looking for a very high quality holster (or any other pieces of high quality gear) from a fantastic small business, look no further than RPS Tactical. Their commitment to their products long after it has left their shop is telling. I have had multiple people come back to me after I have steered them toward RPS Tactical for their holster needs and tell me that they were so happy to work with RPS. Rob and Nick were very attentive to their needs and oftentimes they ended up getting fitted out with belts and other items above and beyond what their original request was. That speaks volumes as to the character and dedication that the guys at RPS have to customer satisfaction. I was very happy to evaluate their holster, and would highly recommend their products to my friends and family, for both duty & EDC use.  

FIREARMS INSIDER REVIEWS - 8 KEY POINTS

CLAIM TO FAME:

Adaptive Holster System (Various Mounting Options)

TARGET MARKET:

Those wanting a high quality holster for everyday carry that can be utilized in a variety of ways.

FNBS (FEATURES & BENEFITS OF THIS PRODUCT):

  • Convertible between IWB & OWB

  • Tuckable during IWB carry

  • Soft side velcro backing against the body

  • Sturdy leather backing with cut to allow full grip of firearm before drawing.

WHAT OTHER AESTHETIC OPTIONS OR FINISHES ARE AVAILABLE?

Various color options/finishes including Kryptek, Carbon Fiber, Coyote Tan & more

LINK TO OTHER REVIEWS:

Tactical Toolbox Review

PRICE POINT:

$65.00 (various options may be extra)

I NEED IT NOW! AVAILABILITY:

RPS Tactical LLC

OUR RATING:

L.A.G. Tactical "The Defender" IWB/OWB holster

  A while back I ran into L.A.G. Tactical. I had heard of them before, but was able to talk with them at the Axelson Tactical grand opening event. I really liked what I was seeing. Later I contacted them and they agreed to send me a holster for review. All of their holsters and accessories are made from Kydex here in the U.S.A.

  Now, as most holster manufacturers do, they make a bunch of different styles and colors. I chose the Defender model in O.D. Green. The Defender is L.A.G.'s combination Inside the waistband (IWB) / Outside the waistband model (OWB). The way they do this is really quit simple, basically they send IWB and OWB belt clips with the holster. Being a style of pancake holster, it uses rivet holes on each end to attach either belt loops or hooks. All the necessary hardware is supplied. Loctite is recommended when attaching the screws, but some of them come with thread locker already on them.

  What sets L.A.G. apart from other holster manufactures is their actual attention to detail. When you go to order one of these holsters, they have drop down menus that ask you just about everything to make the holster fit correctly. Of course one of them is what gun model, of which they have plenty. But some of the other menus are what surprised me. First of which is where the holster will be carried, 2-3 or 3:30-5 o'clock. Then they have a menu for what side of the firearm is the magazine release on. The angle you would like the firearm to sit, 90°, 10°, or 20° cant. Next comes if you are primarily using it IWB or OWB. Now for what I thought was really great, they ask your waist size so they can get the curvature closer to what you need. Along with this, they ask is if you are Male or Female. Then they have a box for special requests. You also can choose separate front and back kydex colors. And last, the size and type of belt loops.

 One can also select the thickness of kydex for the holster. They have standard at 0.060" and heavy duty at 0.080". I chose the standard. But if I had to do it again I would have chose the heavy duty. I like the feel of the thicker kydex and the standard kydex seems to flex a bit. But if it is used primarily as an IWB holster, this flex should make it more comfortable. And since I wore it as both, It did work well as an IWB holster. But I prefer it as an OWB rig.

  The quality of this holster is fantastic. The guns fit inside the holster is great. Draws from both IWB and OWB are nice and smooth. Reholstering is easy thanks to a slightly flared top. The Defender has an adjustable screw tension. So if you want more or less resistance, it is possible. The kydex if formed nicely. Since mine is for a 1911, they have a nicely molded cover over the safety and mag release. I really liked the covered safety as it makes it way harder for the safety to accidentally come off, it also doesn't jab me in the side. The front and rear pieces are also nicely trimmed and smoothed together.

  I carried the holster IWB off and on for about 3 months. It works nicely, and actually made carrying a full size heavy pistol not so bad. It did take about a week for me to get use to wearing it IWB. Having the ability to adjust the ride height helps with the comfort. When I switched it to OWB, and used it at a few pistol matches, it worked very well. Do I have any problems with this holster? Not really, but it does make a better OWB than IWB. But you can't have your cake and eat it too.

  L.A.G. Tactical has also gotten some new publicity in partnering with Tactical Insider and Craig Sawyer on a special Defender series holster. If you are in the market for a good quality kydex holster, do not overlook L.A.G. Tactical. I personally would buy a holster from them or send someone their way. Plus as a bonus they can be purchased from Cabela's, but without all the options available at L.A.G. Tactical's website.

 

Firearms Insider Reviews - 8 Key Points

Claim to Fame:

Kydex Inside / Outside waistband convertible holster

Target Market:

Concealed carriers, IDPA shooters, or General range use

FNBs (Features & Benefits of this product):

  • Kydex

  • Inside waistband carry

  • Outside waistband carry

  • Supplied with both belt clips

  • Adjustable retention

  • Semi-custom for body fit

  • Color options

  • Thickness options

  • Made in USA

  • Adjustable ride height

What other aesthetic options or finishes are available?

Lots of different color and pistol models available

What others are saying?:

Outstanding Holster 5/5 Stars @ LApolicegear.com

I use this LAG Tactical holster set up for IWB with my S&W Shield. Very well made product. all edges are smooth. Molded for perfect fit with my pistol. Very comfortable, even when against my bare skin this summer. Highly recommended!

Pros: Holster completely covers muzzle and front sight -- a big plus in my opinion. Top of outside edge is flared just a bit and that makes "finding" the top of the holster and getting the pistol back in during re-holstering a breeze. Kydex is stiff enough so, when worn, holster holds it shape when pistol is removed -- making re-holstering easy.

Cons: None!

Great holster 4/5 Stars @ LAGTactical.com

Great holster,very comfortable, tight at first but now it is perfect and still retains my pistol very well, has served me well so far, if you are in and out of vehicles all day i would recommend getting thicker kydex as mine is starting to crack, around the trigger guard but that is to be expected as my pistol grip catches on the vehicle during enbus/debus, but i think the next thickness would mitigate that.

Link to other reviews:

LAG Tactical The Defender VP90 @ MajorPandemic.com

Price point:

MSRP = $79.95

Retail = $69.95 @ LAPoliceGear.com

             $69.99 @ Cabela's

I need it now! Availability:

L.A.G. Tactical, LA Police Gear, or Cabela's

Our Rating:

Pros:

  • Available options from L.A.G.

  • Adjustable Ride Height

  • Adjustable retention

  • Convertible from IWB to OWB

  • Includes both style belt loops / clips

  • Semi Custom fit

  • Flared top opening

Cons:

  • Standard Kydex thickness

  • Better as OWB

Score: 8.5 Great

 

Chad’s Favorite Link:  Axelson Tactical

 

Black Iron "ALLY" IWB Holster

  Any one who has considered the idea of carrying a firearm for protection, has had to look into holsters. Almost always, this ends up with a drawer full of unused holsters. The people over at Black Iron Holsters have made the job of choosing a holster a little bit easier with their ALLY series of inside the waistband (IWB) holster.

  The Ally IWB holster is one of the most comfortable holsters I have worn. I am not sure exactly how to describe the ALLY, but think hybrid holster on steroids. The first thing you notice on the holster, is the padding on the back, or the side that rides against your body. This padding is an UnderArmor moisture wicking fabric sewn over perforated padding and then mounted on the flexible kydex core. The padded fabric is said to pull sweat away from the body and make for a cooler drier holster. I did notice that I didn't sweat as much on the holster backing when it was hot outside. But the holster did seem to feel warmer than some other types. The ALLY also doesn't seem to feel cold either, like some all kydex holsters do. 

  When they construct the holster, they use the above mentioned padding, but with some extras. They call it C-Pak. C-Pak adds in a flexible kydex core, 500 denier Cordura fabric, and the moisture wicking and padding mentioned above. All of this helps add to the comfort and usefulness of the holster. The whole holster, except the backing, has been wrapped in the Cordura nylon. This cordura wrapping actually reduces the effects of holster wear on the firearm by giving the firearm something besides the kydex to rub on. They also sew on a border around the whole holster. This border helps smooth the outer edges so that nothing can catch on the them.

  When I mentioned hybrid style on steroids, here is what I mean. The holster is constructed with a large backing plate and then the outer holster is attached to it. But all of this is wrapped as mentioned above. They also put in a tension adjustment screw so that you can adjust it to your preference. The backing on my supplied holster has 3 holes for each clip, it has a front and rear clip. These holes make it possible to adjust for ride height and cant. Also the supplied nylon clips have 2 mounting screw options for even more adjustment. Even with the clips mounted in the same holes on the backing plate, the cant of the firearm is pretty noticeable. I did have a problem with the screws, that the clips are mounted to, coming loose. I put thread locker on them, but got some on the nylon clips. DON'T get threadlocker on the clips, it might make them crack and break like in my case. I emailed Black Iron and told them what I did, within a few days they had sent me new clips. I was just going to use some others I had around here since it was my fault they broke. So a big +1 for customer service.

  Aside from this being a very comfortable holster, it is also very functional. This holster has a little bit of break in time associated with it, like 2-3 days. After that, I didn't really even notice it. One of the great features of the ALLY is that the holster mouth doesn't collapse when the pistol is removed. Thus making reholstering safer and easier. Holstering the pistol was a little strange at first, I kept wanting to here the audible click like most hybrid or kydex holsters. But it felt more like an all leather holster. Don't be worried about this holster printing either. It has a very smooth profile. I did notice that it is slightly thicker than some holster due to its padding and cordura, but the smooth profile made up for this. It is hard to notice this holster being worn. I usually only hide it under a T-shirt and that works well.

  Now, the ALLY comes in the four different fabric colors listed below. But don't fret, they seem to make this holster for just about every popular, and even other not so popular handguns. Also with options for various weapon lights. If they don't list your handgun, their website says to contact them, which makes me think they will do their best to help you out. So if your in the market for a nice IWB holster, give Black Iron Holsters a look. 

Firearms Insider Reviews - 8 Key Points

Claim to Fame:

Soft/Comfortable Inside the waistband kydex holster

Target Market:

Concealed Carriers

FNBs (Features & Benefits of this product):

  • C-Pak Backing
  • Cordura wrapped
  • Hand washable
  • Made for each individual firearm
  • 1.5" clips
  • Adjustable for ride height and cant
  • Tension adjustment
  • Breathable
  • Flexible
  • Cerakoted hardware
  • Made in U.S.A.

What other aesthetic options or finishes are available?

Coyote, Multicam, and Multicam Black

What others are saying?:

Great Holster, Buying More: Roger from BIH 5/5 Stars

I received my holster 2 weeks ago and this is by far hands down the greatest holster i have ever used. It fits like a glove both on myself and for my glock. It is everything described and more, i am a delivery driver and spend the majority of the time on the road getting in and out of my truck. I can honestly say by the end of the day it was so comfortable i completely forgot i was wearing it by the end of my shift. I will be swapping out my Alien Gear holsters for my other two guns and will be ordering everything from you guys from now own. Its well worth the few extra bucks for something that is of this quality.

Great Products and Service: Timothy from BIH 5/5 Stars

First of all let me say that my experience with customer service was exceptional, I had a lot of questions concerning which style of holster to purchase and what was going to work for me. The staff at Black Iron was very knowledgeable and evidently knew what questions to ask and how to explain things because this is the best fitting and most comfortable holster i have ever worn. If you have any doubts about buying one don't you will be blown away by these things.

Link to other reviews:

Nothing found while googling

Price point:

MSRP = $79.95

I need it now! Availability:

Black Iron Holsters

Our Rating:

Pros:

  • Comfortable

  • Holster mouth stays open

  • Flexible

  • Adjustable retention

  • Tuckable

  • Adjustable Cant and Ride height

  • Firearm options (lights, lasers, models)

Cons:

  • Sewing of fabric looked poor (Not straight)

  • Slightly thicker

  • Clip mounting screws come loose (Maybe supply pre-threadlocked screws)

 

Score: 7.5 Good

 

Chad’s Favorite Link: U.S. Tactical Supply  

 

 

 

Alex & Ryan Design Kydex Light Bearing Holster

I first heard of Alex and Ryan Design from my friend who bought a cuff holster from them. I looked into them a little bit and sent a few emails back and forth. After getting their advice(they answer their own email) I ordered the holster featured here and a double mag holster for IWB. I very promptly received an email from Alex saying that he thought it’d be more comfortable if I had 2 single mag holsters.

IMG_0508.JPG

I went with his recommendation as he’s the expert. When I received the product I was a little shocked that it came in a plastic shipping bag as opposed to a box but my fears were immediately set aside as I inspected the holsters for damage. They’re definitely strong and durable to travel through the postal system unscathed. I grabbed my Glock 19 with Inforce APL and quickly, yet safely, inserted it into the holster, and then the whole contraption into my pants. I decided that it needed more retention so I removed it and tightened it with a coin, like many other smart designs allow. After some trial and error I got it to a retention level that I felt comfortable with.

The inside of the holster is smooth and allows for quick retrieval of your weapon while the outside has the familiar feel of kydex, rough yet soft. Wearing this has been a breeze and comfort has never been an issue. I've since wore it to two weddings, one of which I was a groomsmen, and no one had a clue. I recently tripped while running and the holster held up, kept my firearms secure, and only suffered some light scratches. A nice thing about its design is that I’ve successfully carried this setup as appendix, on the hip, behind the hip, and small of back positions. The clip on it is very sturdy yet still flexible to enough to bend far beyond any belt they can accommodate. I’m unsure of a way to make it any better without the addition of adjustable cant.

Claim to Fame: Comfortable and quality holster

Target Market: Concealed carriers

FNBs:

  • Custom made to your setup
  • Many firearms choices
  • Adjustable retention
  • 10 degree cant optional(non light bearing)
  • Options for different lights
  • Suppressor sights chanel optional
  • Optional lifetime warranty on all parts and hardware
  • 3 different sweat guard heights

What other aesthetic options or finishes are available?

There are too many for me to list so here’s a couple cool ones: Multicam, Tiffany Blue, 9 Kryptek designs, classic black, and many more.

What others are saying?

You can find reviews on their site for this holster

Price point:

$48.99 and up depending on options chosen. $65.99 as designed in this review.

I need it now! Availability:

It’s a custom made product so it takes 2-3 weeks to produce depending on their other orders. There is an option for rush orders and they’ll ship in 3-5 business days.

Our Rating:

Pros:

  • Tough design, .080 thickness
  • 100% American made using American made hardware and equipment
  • Full combat grip
  • Easy reholstering (kydex retains weapon shape)

Cons:

  • Preset 0° cant on light bearing, 0° or 10° degree cant on non light bearing
  • Neutral: At the time, it wasn’t offered at Appendix with RCS claw. It is now offered as such.

Score 8.5

 

Osborn TacticalTuck IWB holster

  So a few months ago I was looking for an IWB holster for a SCCY pistol. I was specifically looking for a hybrid style and ran across Osborn Holsters out of Texas. They pretty much only offer hybrid style holsters. Some of them even have a mag carrier built in with the holster. I chose the standard style without the extra mag carrier. Osborn sent it to me for review and it arrived quite quickly. 

   I have been wearing the TacticalTuck since it arrived about 2 1/2 months ago. The holster is dyed a redish brown color. Osborn holsters informed me that dyed holsters resist sweat better, but I notice now they offer a moisture barrier for an extra few bucks. It can also be had in natural or black leather. 

  The TacticalTuck has been one of the most comfortable holsters I have worn. It uses a very flexible leather backing with a kydex outer shell.  This has its pros and cons. On the positive, it is super comfortable. On the negative, it is hard to reholster because it pushes in toward the kydex, somewhat collapsing the pocket that the firearm goes in. As long as you pay attention and reholster slowly, it works out fine. The outer shell is molded for your firearm. And they have lots of models to choose from. Osborn does a nice job on the shell. My firearm fits good, there are no sharp corners and the molding around the gun is done nicely. The shell is also adjustable for tension with 4 screws that press on rubber washers. All the hardware screws use a smooth, chicago style, backing nut. 

   Osborn supplies their holsters with metal belt clips. These clips are some of the sturdiest clips I have used. The TacticalTuck has 2 belt clips to give a sturdy attachment of the holster. The clips have bumps on them that help them stay on around the belt. I had zero problems with the loops coming off. In fact, they clip on so well that it actually takes some effort to get them off of the belt. I like these clips, but every metal clipped holster I have used, causes my shirts to wear out. Especially around the rearward clip, when sitting in chairs alot, the clip rubs through the shirt.  

  Being that this is a hybrid style holster, it offers plenty of adjustments. Each belt loop has 4 adjusting holes. So by moving them up or down individually one can adjust ride height and/or cant of the holster. Each one of the holes has been riveted, so adjustment is easy and the holes should not wear out. Osborn also cuts the backing leather for the individual firearm. This is a nice touch, as other companies sometimes just use 3 or 4 different backings. 

  Osborn makes a nice holster. It has some good features and a few so-so ones. But if your in the market for a very comfortable hybrid holster. Give Osborn Holsters a look. 

Firearms Insider Reviews - 8 Key Points

Claim to Fame:

Hybrid style IWB holster

Target Market:

Concealed carriers

FNBs (Features & Benefits of this product):

  • Hybrid style (leather back, kydex shell) 
  • Firearm Model availability
  • Adjustable retention
  • Steel belt clips
  • Tuckable 
  • Adjustable ride height
  • Adjustable cant
  • Made In U.S.A.

What other aesthetic options or finishes are available?

Natural or Black

With mag carrier combo

What others are saying?:

 Good Holster

Mike @ Osbornholsters.com 4/5 stars

Overall it is a good holster. I like the adjustability of ride hight and the quality is great. My only complaint so far is the retention. I have tightened the screws as far as they will possibly go and the leather seams to relax the more I wear it loosing the retention. I have bottomed out the screws and not sure where to go from here.

 

Great Options for Rail-Mounted Lights

Z @ Osbornholsters.com 4/5 stars

Pros: * Overall solid build quality and features.* If you have a weapon-mounted light (and you should), there are more options available on this holster than with most other vendors.Cons: * Had to cut off some leather to allow my middle finger to get under the trigger guard on the draw. * Then had to trim a bit of kydex to allow my middle finger to index under the trigger guard on the draw without scraping it on kydex every time.

Getting a consistent and proper grip is paramount. The strong hand should ride high and tight into the backstrap/beavertail, and the middle finger should ride high and tight into the trigger guard. Google "maximizing the combat handgun grip" for more info. Just trim the leather and kydex a bit to allow this the moment you grip the pistol and you have a product that can't really improve much further.

Link to other reviews:

Four Guys Guns

Concealed Nation

Price point:

MSRP = $49.99

I need it now! Availability:

Osborn Holsters

Our Rating:

Pros:

  • Comfortable
  • Adjustable retention
  • Adjustable cant
  • Adjustable ride height
  • Quality molding
  • Tuckable

Cons:

  • Collapsible holster mouth 
  • Metal clips

Score: 7.5 Good

 

Chad's Favorite Link: The 22 Connection

 

Crew Holsters "OL' Classic OWB" Holster

Crewowb1

The Crew Custom Holsters OL' Classic OWB is your standard outside the waistband holster.  It is manufactured from some nice heavyweight kydex or similar plastic.  The one I received is for a full size 1911 style pistol.  It arrived in black.  I tried it with 2 different 1911's and it functioned flawlessly.

Crewowb2The design of the holster would make it very useful for everyday carry, IDPA, hunting, or any other thing you might want an outside the waistband holster for.  The belt loops supplied fit my 1.5" belt nicely.  The loops are also kydex, and are very deep, meaning that a really thick belt, or one of the double competition style belts, will fit through the loops.  The loops can also be adjusted up or down on each side.  This way, the holster can be lowered, raised, or adjusted for cant.  Being that it is for a 1911, the inside sheet of kydex came up just to the safety lever.  The outside piece is a little lower to help you get a good grip when drawing.  This model OWB holster also covers the trigger guard completely.  It is also molded around the mag release button so that it can't be hit accidentally.  Some of the owb models have adjustable retention, this one does not.  I didn't find this to be a problem, as the holster retained the firearm nicely.  The draw stroke is also very smooth. Upon reholstering, you do get a good "snap" as the holster locks the gun in place.  I did notice that it took a few draw strokes to break in the holster, as it was very snug when I first received it.

This holster is really nice.  It is available in lots of colors and patterns, for a few extra bucks.  There are also options for weapon mounted lights and lasers.  Various belt clip options are also available, as well as a sweat guard, if one wishes.  The only flaw I found with this particular model was that, with one of my 1911's, the safety would just touch the holster so that the firearm would not go in completely.  I mean by maybe an 1/8".  So I just filed that spot down slightly and it worked great.  I called The Crew Holsters about this and they said I could send it in for them to fix, because it does have a lifetime warranty.  They said they would look at the problem and I doubt that it exists anymore.  If you're in the market for a good kydex style holster, give the Crew a call.

Crewowb3

Firearms Insider Reviews - 8 Key Points

Claim to Fame: Outside the Waistband holster

Target Market: IDPA, concealed carriers, hunters

FNBs (Features & Benefits of this product):

  • Adjustable belt loops
  • Available Options
  • Full trigger coverage
  • Good retention

What other aesthetic options or finishes are available? Lots of different colors, patterns and options.

What others are saying?: 

  • THE STUTTERIN GUNNER from YouTube
    "I've ordered a few of their iwb holsters and i think i found the last holster company I'm going to deal with, the owner is cool and prices are damn good, and the product is good, speaking of which i need to order a iwb for my sig."

Price point: 

MSRP = $45.00 for black, everything else extra

Retail = $45.00+

I need it now! Availability: The Crew Custom Holsters 

Our Rating: 

Pros:

  • Good Retention
  • Adjustable Belt loops (height and cant)
  • Firearm availability
  • Color and pattern options
  • Light and Laser options
  • Belt loop options
  • Adjustable retention on some models
  • Completely covers trigger

Cons:

  • Safety on 1911 hit edge of holster slightly

Score: 8.5+  Grea85t

 

 

Chad's Links:

Handgun Radio

Man O' Steel charity fund raiser multi gun challenge

Firing Line Review

 

 

Alien Gear Cloak Tuck 3.0 IWB Holster

Alien Gear Cloak Tuck 3.0 Holster

Following up on my past review of the Alien Gear Cloak Tuck 2.0 Holster, I requested the newest evolution to the extraterrestrial themed holster line, the Cloak Tuck 3.0 Holster. I gave the Cloak Tuck 2.0 IWB holster a rating of 6.5 out of 10, as it was a uniquely comfortable holster, but had some odd flaws that should probably have been thought out better. The cons I found with the 2.0 holster was the generous flexibility of the backing would cause the slide to come out of battery when reholstering at a wrong angle, instead of guiding it into position like a more rigid leather backing. The neoprene material was soft and comfortable, but the smooth front surface lacked enough friction to really hold the gun snuggly. Another big complaint was the exposed hardware on the back that would contact the skin and cause slight discomfort. The cant adjustment hardware also was exposed on the front and would wear the fabric of your pants. No bueno! But it was apparent Alien Gear was onto something, as many users still raved the 2.0 holster.

Alien Gear Cloak Tuck 3.0 Holster

The quest for engineering a superbly comfortable, yet functionally supportive IWB holster is a tough egg to crack. Many IWB carriers are simply content with their leather backed holster, and pretend its comfortable when in reality it feels pretty noticeable on the hip or has a bulky profile that prints through the pants or shirt. Alien Gear's cloak tuck line has gone through a several design and engineering phases, from a high quality leather backing in the first version, to the cloak tuck 2.0 and it's neoprene covered ABS polymer core. In this third creation, Alien Gear has found much more than a compromise.

Alien Gear Cloak Tuck 3.0 Holster

Alien Gear Cloak Tuck 3.0 Holster

The Cloak Tuck 3.0 doesn't compromise in comfort at all. In fact, its even more comfortable than the 2.0, which many users raved about it's almost nonexistent presence on the belt. The neoprene backing is just a soft, and now it covers the unsightly hardware T screws. No more will body hair get snagged and pulled! To boot, there is now only one set of cant adjustment screws, that you can simply unscrew and reposition however you like using the supplied allen screw. I can't really think of a reason why there were two sets of unused and exposed screws on the 2.0 holster, but thankfully they're gone!

Alien Gear Cloak Tuck 3.0 Holster

The biggest improvement to the design is on the inside, beneath the neoprene fabric. Instead of an ABS core, there is now a stainless spring steel backbone dow that is only big enough to anchor the gun shell itself. The wings of the holster still remain very flexible, bendable to a full 180 degrees without tearing, breaking or stretching anything. So now not only does the handgun have a more rigid but flexible support backing, but the winged tabs are free to flex along your belt-line more freely. The backing carries the same combat cut as the previous models, and it has the same flexibility as the wings so no matter your body type or degree of muffin top, this holster wouldn't feel any more comfortable unless it was made of Charmin Ultra Soft.

 

Alien Gear Cloak Tuck 3.0 Holster

Another new addition to the Cloak Tuck 3.0 has a new skin. Specifically called "Alien Skin," the front surface of the holster now has a thermoelastic layered thats textured almost like a reptile. The new texture adds drag to the retention of the pistol, which was lacking in the 2.0's smooth surface. Also the Alien Skin has the logo and made in USA flag molded right into it, which looks much more professional than the silver paint on the last version.

Alien Gear Cloak Tuck 3.0 Holster

Nothing's changed as far as the clips and handgun shell, they are exactly the same as before... well expect now you can get a Viridian reactor model that activates the laser upon draw. As for the belt clips, you can choose from a number of clips including black steel clips, standard nylon clips, polymer injected "J" clips or "C" clips, black leather loops, tan leather loops, or as a combo of black leather loops and either "J" clips or "C" clips, or tan leather loops and either clips. The "J" clips come up over the pant and hook just underneath the belt, and the "C" Clips hook over the top and bottom edge of the belt. These two styles are supposed to be more discreet when you have your shirt tucked in, as any full size clip showing over the top of a belt when the shirt is tucked is really a dead giveaway. It's what I look for first if I'm playing the "spot who's carrying" game. The black or tan leather loops are intended to "blend" against your black or tan dress belt for more discretion as well.

Alien Gear Cloak Tuck 3.0 Holster

Alien Gear Cloak Tuck 3.0 Holster

My review score for the Cloak Tuck 3.0 goes up to solid 9.0, with a high probability of it meeting a 9.5 rating after further testing to be sure the stitching and overall finesse holds up over time. Bottom line, this is the most comfortable inside the waistband holster on the market... regardless of price point. While there are comfortable options out there, you won't find one that beats the price of the Alien Gear Cloak Tuck 3.0 holster. Easily affordable, easily adjustable for cant and retention, and easily forgettable when wearing unless you bend or contort. I wish I could say they paid me for a glowing review, but the fact is this is just a damned good holster. The branding of Alien Gear is alittle oddball with the whole little green man and UFOs on the website, but its hard to dispute their claim that this is "the most comfortable holster on Earth," or at least until the Cloak Tuck 4.0 holster comes out.

Firearms Insider Reviews – 8 Key Points

Claim to Fame: The Cloak Tuck 3.0 concealed carry holster offers an unmatched level of comfort and concealability within the concealed carry world.

Target Market:  Concealed Carry

FNBs (Features & Benefits of this product):

  • Holster base can be used to upgrade Cloak Tuck 2.0 Holster
  • Improved retention
  • Enhanced flexibility
  • Stainless spring-steel band that acts as core
  • Layer of thermoelastic polymer w/ "Alien Skin" covers the face of the gun holster for grip
  • Previously exposed T-Nuts are now covered with soft neoprene fabric on the back
  • Completely waterproof design
  • Compatible with a variety of belt clips: nylon “C” clips and “J” clips
  • Great variety of gun models, even obscure guns other holster makers don't touch
  • Available for some guns with mounted Crimson Trace, Viridian or Laserlyte products
  • Hosts multiple shells, allowing user to swap out their guns while keeping the same holster base
  • Iron Clad Triple Guarantee: 30 day test drive, free shell trades for life, and Forever Warranty.

What other aesthetic options or finishes are available?: Black "Alien Skin" with Bright Green Bushings

What others are saying?: "Alien Gear Holsters: Is it Hype or Quality? I've seen the slick marketing and all the ads but figured it was a cheap design considering the price. 

  • Alien Gear Holsters produces Hybrid holster system high quality leather backing with
  • Variety of clips for customizing carry options for unbelievable comfortable all day long
  • Distributes weight across waist with no issues whatsoever
  • One of the cool things about the system is you get an accessory pack with clips, hardware and wrench - everything you need to customize, make it your own the way you like. 

I think theres a lot of cool things about these holster that will peak your interest. It has mine." sootch00 YouTube Video

Price point:

I need it now! Availability: Website

Our Rating:

Pros:

  • Extremely Comfortable, yet good support of the handgun
  • Carries well in different positions on the hip, angles handgun grip inward
  • New spring steel core increases retention by stiffening weapon area while still allow wings to flex
  • Thermoelastic skin and hidden T Screws are vast improvements to aesthetics over 2.0
  • Extra parts now come in a sweet little kit with different size screws and bushings and a alien head keychain (lulz)
  • Customer service is on point
  • Price beats out most other competitor IWB holsters
  • Great entry level option for new concealed carriers

Cons:

  • Position of the slide was still slightly off center from sweat guard
  • Limited options for popular weapon lights (no Streamlight, Surefire, Inforce)

Score: 9.0 Amazing

Featured FFL:

For FFL services I choose Promised Land Firearms in Toulon, IL.

Ryan's Links:

Gun & Gear Review Podcast

Hunter of Design

Firing Line Review

 

 

Bravo Concealment RTT Holster Combo Pack

Bravo Concealment RTT Holster Combo

I remember listening to a podcast back when I first became a gun owner, and one of the hosts jokingly claimed that when you become a concealed carrier, you are almost guaranteed to have a drawer full of holsters at some point. Sure enough I can support that claim now that I have multiple handguns, each of them needing a holster for inside the waistband (IWB) or outside the waistband (OWB) carry. Add in a mounted weapon light, and thats another set of holsters. The good news is many other gun owners have the same problem, and kydex holster companies have attempted convertible holsters that can easily be swapped between OWB and IWB.
One such holster is the RTT Holster from Bravo Concealment. Available in a combo pack that includes both IWB and OWB belt clips for either training or competition use, or carrying concealed inside the waistband. The combo pack also includes kydex magazine holsters, either as two single mag pouches or one double mag pouch.  The RTT holster is designed to fulfill most of the requirements for a defensive pistol class setting, all for one solid price.

Bravo Concealment RTT Holster Combo

The RTT Holster gets it's name from Range Time-Tactical Shooting, LLC. You maybe more familiar with their YouTube Channel of gear reviews and training promo vids. The RTT Holster Combo Pack is marketed as the gear package ideal for taking a RTT Defensive Pistol Class. Bravo Concealment offers the RTT holster separately as a lightbearing or plain standalone holster for $74.99 if you already have mag pouches you prefer to run in the classroom or competition, as well as the standalone magazine holsters as either double, or two single magazine pouches.
 In wearing the RTT holster and mag pouches around the farm for a week with my Smith & Wesson M&P357c w/ Streamlight TLR3, I really appreciate the robust construction and the hand-fitted care that when into the components. The inward curve of the belt loops on the holster and pouches fits the natural curve of the body as well as provides good friction against the belt, so your rig wont be sliding around your waistline all day.

Bravo Concealment RTT Holster Combo

The advantage to selecting two single mag pouches is the flexibility on the belt, you can either place both side by side on the support hand side, just one, or mix it up to fit your training scenario. There is an option to have the bottom edge of the kydex pouch cut slanted to allow for better mobility during pronating or crouching exercises. Another great feature Bravo Concealment puts into these mag pouches is a tensioning screw just to the right edge of the magazine that can be tightened or loosened with a screwdriver. Most holster makers will tell you to heat up the kydex to be pliable enough for manually reforming, but its nice to see this maintenance step simplified into the engineering of the mag pouches. Logically they will be used more frequently that the main handgun holster during courses of fire (unless your only practicing your drawing mechanics) so its nice to able to adjust the tension on the fly.

Bravo Concealment RTT Holster Combo

The RTT holster itself is an all around good OWB holster. Strictly speaking, outside the waistband kydex holsters all sort of look the same. The key differences between them to me are the cut and the clips. By cut, I mean the top opening of the holster. There's a balance thats needed in order to protect the trigger guard yet expose the magazine release, as well as leaving adequate clearance for the gripping hand's fingers to get a full, firm purchase on the handgun's grip... especially under duress. Several draw-strokes under standing, sitting, and kneeling positions were all positive in my testing.
The clips, or belt loops in this case, are what I would consider and great choice for OWB carry and training scenarios. Instead of using actual clips that would allow the holster to be attached or removed without unfastening the belt, Bravo uses polymer injection molded belt loops. These require the belt to be threaded through the loops at the same time as your pant belt loops, unless you run an exterior tactical belt which of course is possible by selecting one of the 1.5" - 2" belt width options on the Bravo concealment website. These loops are really ideal for heavy duty drills and generally harder use than other style clips, as they will withstand more stress from drawing and reholstering forces. I've seen other OWB kydex holsters on the market with thinner belt loops cut from the same kydex sheet and I was never really impressed by their thinness and sharp edges. Also a note: Bravo offers pancake-style belt loops separately.

Bravo Concealment RTT Holster Combo

This brings me to the IWB capability of the RTT Holster, which for me did not go well. My real only issue with this holster as an IWB option is it was very uncomfortable for a shooter my size.  I carried it in the 4 o'clock position like I'm accustomed to carrying with other IWB holster types, and just feels like a huge hard object not conforming to my hip at all. For context. my build is north of 220lbs, and the holsters I usually wear for CCW are leather backed with a half kydex shell.  I've tried adjusting the RTT to an appendix carry position, and an almost 5-6 o'clock position to reduce the direct pressure on my hip with some relief, but still just not feasible for me unless 5.11 decides to make tactical sweatpants.

Bravo Concealment RTT Holster Combo

Now take note, if you have a slimmer body type, this holster should ride better on your hip. However with that said, I also found difficulty with the IWB soft clips themselves as they interfere with the drawing hand. Even with the clips mounted at their lowest position on the holster's grommets and adjusted for a 1.25" width belt, there wasn't enough clearance for my fingers when drawing the weapon, and I by no means have sausage fingers! My second grievance is they are tricky to loop under the belt and snap with one hand or without looking. I'm not sure why the button snaps themselves were so difficult either, but I wasn't able to figure out how to snap them correctly in one attempt. These are just not working for me, but it is worth noting that Bravo Concealment also sells polymer injection molded IWB belt clips that would be preferable in my opinion over these soft belt clips.

Bravo Concealment RTT Holster Combo

All in all, I would certainly recommend getting the RTT Holster Combo Pack if you wanted a starter's kit for training courses or competitive shooting events, especially if you wanted to retain a mounted weapon light on your gun using an outside the waistband holster. If your class / competition requirements include a IWB holster and you are confident this style of holster will fit inside your pants, I would say get the 1.5" or 1.75" IWB belt loops instead of the soft clips. The gear is solid, and the customer service at Bravo Concealment is on point. Now get your gear and hit the range!

Firearms Insider Reviews – 8 Key Points

Claim to Fame: The RTT Combo Pack provides everything needed to attend an Range Time Tactical Defensive Handgun Class. Whether you are a casual shooter or a serious RTT enthusiast, the RTT Combo Pack will help you purchase everything you need at a discounted price.

Target Market:  CCW carriers (OWB or IWB), Handgun Training Classes, 3-Gun competitors

FNBs (Features & Benefits of this product):

  • Kydex RTT Holster available with or without pistol light.
  • 2 Single Mag Pouch *OR* 1 Double Mag Pouch
  • IWB Soft Belt Loops/ IWB Belt Clips
  • Designed for outside the waistband carry, but can easily be converted to inside the waistband by switching out the belt loops.
  • Thinner profile and 0° cant allowing the ability to add more gear to your belt.
  • Hand molded holster for solid retention of weapon.
  • Robust 1.5” or 1.75” injection molded belt loops.
  • Adequate room for a positive grip thus enabling a smooth draw with solid weapon retention.
  • Belt loops are adjustable to create a desired cant for greater concealment.
  • All edges on holster are rounded for comfort.
  • Kydex .08 thick
  • Bravo Velcro Patch

What other aesthetic options or finishes are available?: Black, OD Green, Flat Dark Earth, Coyote Brown.

What others are saying?: "I bought the RTT holster to support the Indiana company it was named after. I carry the G19 and love the holster. High quality, thick kydex. I bought the holster along with a single mag holder. Perfect retention, plus I love the fact that there is a cutout for the index finger so I can get a FULL grip before drawing. I did have to wait 3 months to get it, but it was worth it for me. I don't buy a lot of gear, but what I do have I like to spend the extra time and money to get the best I can afford. I feel like I made a good decision. I would not hesitate to purchase again from them." DefensiveCarry.com Forum User

"I recently picked up the ‘RTT Holster’ from Bravo Concealment and wanted to share my thoughts on the holster. Let’s start with customer service. The fit and finish on Bravo holsters are stellar. I was very impressed with the quality and attention to detail that was evident in the holster I received. My holster was free of sharp edges and rough spots throughout. Not to be disappointed, function follows fit and finish with everything Bravo makes. My holster was for a Glock 17 and the retention was excellent. My Glock clicked into the holster and stayed in place until I wanted it out. The ‘RTT Holster’ is designed primarily as an OWB holster and that’s how I use it. Given the way the holster curves around the body and the way the belt loops pull the holster close in, the holster conceals quite well. Options are available for IWB use if you’re interested. I’ve run the Bravo Concealment ‘RTT Holster’ through two handgun classes and use it for concealed carry on a daily basis and I couldn’t be happier with how it performs. Having purchased my holster for the Glock 17, I actually got a bonus feature in the since that the holster also works very well with the Glock 19 & 26." Shanes Gear Thread

Price point:

  • Retail: $142.99 -10% using coupon code RTTCOMBO10

I need it now! Availability: Brave Concealment Website

Our Rating:

Pros:

  • Convertible from OWB to IWB using supplied clips
  • RTT Holster is well made with solid retention
  • Hardware are common screw heads instead of hex or torx
  • Mag pouches available as two singles or one double pouch
  • Slant cut on mag pouches for better mobility / shooting positions
  • Mag pouches have tension screw for user adjustability
  • Holster and mag pouches are adjustable for cant
  • Injection molded belt loops are tough and rugged
  • If your pistol has an RMR or other micro red dot, Bravo will cut a recess for clearance

Cons:

  • Concealed IWB carry is not as comfortable as other IWB only holsters
  • Soft belt clips hinder clearance for drawing hand
  • Price still higher than separate components on the market

 

Score: 7.5 Good

Featured FFL:

For FFL services I choose Promised Land Firearms in Toulon, IL.

Ryan's Links:

Gun & Gear Review Podcast

Hunter of Design

Firing Line Review

 

 

 

Crew Holsters "Shadow" IWB Holster

crewholster5 Photo_2015-06-08_09-02-28_AM

I received the Shadow holster from "The Crew Custom Holsters" some time ago.  The Shadow is a kydex clam shell style inside the waistband (IWB) holster.  I have been wearing the Shadow for a while to try it out.  It is comfortable for a kydex style holster.  The model I received was in black, but they offer lots of different color and pattern options.  They also offer the Shadow for light or laser mounted firearms and tons of different models of firearms.  You can wear it just about anywhere from appendix all the way around to about 5 o'clock.  I typically wear it around the 3:30 position.  It seems to conceal the firearm well, as my children and wife did not notice me wearing it.  One big advantage this holster has over others is that it can be canted frontwards or even backwards.  There are different holes where the clip is located to adjust it to Zero, 15, or 45 degrees.  I tried it in all 3 positions and found that the zero and 15 worked best.  The 45 degree cant seemed strange, but someone may have a use for it.  The fit and finish of the holster are very good. They smooth the edges out and try to eliminate any sharp surfaces.  Mine is for a Kahr CM9 and it fits nicely and, with the adjustable retention, holds the pistol well.  The holster does collapse a small amount when there is no firearm in it.  It didn't seem to collapse enough to make reholstering difficult, but I did notice it.  I usually wear a hybrid style holster, but have found that with this little holster, the single clip makes it ideal to slip on and off easily.  If I need to run to the store at night or something similar, I can just grab this holster and clip it inside my waistband with no problems.  The Shadow is a very nice, convenient holster.  They will also do custom one off holsters if asked.

crewholster4

Firearms Insider Reviews - 8 Key Points

Claim to Fame: Convenient IWB holster

Target Market: Concealed carriers

FNBs (Features & Benefits of this product):

  • Adjustable cant
  • Lifetime warranty
  • Single wide clip
  • Adjustable retention

What other aesthetic options or finishes are available? Lots of different color and pattern options

What others are saying?:

  •  5/5stars at The Crew Custom Holsters - Quick and excellent, communication, product and service. I have been recommending The Crew Holster to my friends.

Price point: 

I need it now! Availability: The Crew Custom Holsters.  Some options ship quicker than others, see Available Molds

Our Rating:

Pros:

  • Adjustable Retention
  • Adjustable cant
  • Light options
  • Color options
  • Easy on/off

Cons:

  • Slight holster collapse

Score: 8.5 GREAT85

 

 

Chad's Favorite Links:  Handgun Radio

ABC House Charity Match June 20th, it really is for the children!

Firing Line Review

 

 

Sticky Holster

Sticky4.jpg

Sticky4 I’ll start off this product review by admitting that I am someone who is very hard to please when it comes to holsters. I think that may be a majority of the people who carry as well, but I am especially difficult in this regard. I absolutely hate tucking in shirts, and nothing is more annoying to me than having my firearm rubbing into my side all day. Because of this, I have been mostly relegated to pocket carry for the majority of my life. A good pocket holster should break up the outline of the firearm, as well as create a margin of safety by covering the trigger guard. An IWB holster should do the same thing. With most pocket holsters, retention of the holster on the draw is accomplished by having either a small hook-like appendage on the holster to snag on the pocket during the draw, or a sticky substance on the outside that tends to snag on the pocket material during the draw. Most IWB holsters accomplish this retention by using some sort of a belt clip, either plastic or metal (or button loops on some designs) that retain the holster in the pants during the draw stroke. The Sticky Holster uses the tacky outer surface material do accomplish this. However, the idea behind the Sticky holster goes much further than just pocket carry.

The Sticky Holster can potentially serve as a pocket & IWB holster

The Sticky Holster is designed to be quite versatile. The models that are designed for smaller framed guns, like my J-Frame, can be used one of two ways; either as a traditional pocket holster in a pants pocket, or as an IWB holster, wherever the user would prefer the firearm. Some guns are more suited to IWB carry than others, and some guns are more suited to pocket carry than others. It all comes down to personal preference. That would be one place where I would say the Sticky Holster shines. Rather than the user needing to purchase two separate holsters for two different modes of carry, the Sticky Holster can function either way. If you get up one day and decide that the pants you’re wearing have big enough pockets for pocket carry, you can put your firearm in the Sticky and put it in your pocket. If you decide that the pants you have on don’t really support pocket carry, you can tuck the whole firearm and holster unit into your waistband between your side and your belt and carry it IWB. The clipless design allows for the user to put the holster and firearm wherever on their beltline they would prefer, and this could be a significant advantage, as some pants have belt loops that tend to always be in the EXACT location where you want to put the firearm. Not having to contend with the exposed clip allows for many more location options.

The Sticky Holster uses a tacky outer material for holster retention

For my test & evaluation purposes, I was provided with the MD-5 size holster from Sticky. It is designed to hold snubby revolvers with a barrel length up to 2.125”. It fit the revolver well, and the quality of construction and materials were quite nice. I must admit, this is my first experience with a holster of this style, and many of the things I experienced when using the Sticky holster could be chalked up to my inexperience with the system. When pocket carrying the Sticky holster, the retention was good during the draw, and the holster covering the hammer helped to prevent any snags during the draw. One of the negatives I found when pocket carrying with my J-frame was that there seemed to be quite a lot of extra material toward the bottom edge of the holster. This was causing the holster and gun to be pushed up and somewhat out of my pocket slightly when I sat down in the car. Perhaps this could be an issue with the pants I wear (Carhartt’s) but could also be an issue with a little too much material on the holster. It's not a deal breaker for the product, but something to be aware of for those folks who are buying the Sticky as a main pocket carry holster.

The Sticky covers the hammer of my J-Frame. This aids in carry comfort.

Carrying IWB with the Sticky holster is pretty easy, but it does take some getting used to for those people who are accustomed to having a clipped IWB design. The Sticky uses the compression of your belt against your side in conjunction with the tacky material to afford retention of the holster and firearm. I tried this with several different types of pants and gym shorts and found myself to be most comfortable with the Sticky while using normal pants and a belt for retention. There were a few times that after fast running or jumping that the Sticky had moved from where I had originally placed it. I had a similar issue with it while sitting down in the car. This could be a function of my body type and the type of seats I have in my vehicle, but it is something for the prospective buyer to be aware of. There is versatility in this holster, but it may not work for everyone, depending upon your lifestyle and comfort level. I have heard people talk about using the Sticky as a holster for when they are wearing pants or shorts that are not meant to be worn with a belt, and that use a simple drawstring for compression around the waist. I tried this several times, but the Sticky holster just did not feel secure enough for me in the waistband for me to trust this method of carry with that style of pant. Granted, I am carrying a very NON-lightweight J-frame (Stainless Model 60) so that method of carry may work better for people carrying a lighter weight weapon, but for me it just didn’t work out as well.

In closing, the Sticky holster is a good product that does help out in the holster decision process. It offers a versatility you sometimes won’t find with other holsters, and does so at a competitive price. I see that Sticky is planning on offering a reinforced model soon (Spring 2015) and that should alleviate some of my concerns with the thickness of the material. The instructions provided with the Sticky are clear and conscise, and explain the process for safe use of the holster, as well as the cleaning process (Which is very easy!). If you are someone who needs a versatile holster, and just can’t seem to find one which fits your needs, check out the Sticky Holster. It did not work well for me as an IWB holster, and worked best as a pocket style holster, but it may fill the IWB & Pocket Holster needs for you!

Firearms Insider Reviews - 8 Key Points

Claim to Fame: This product is a holster that is designed for use either in the pocket or inside the waistband. It is a clipless design that uses compression from the pants/belt and a tacky outer material to retain the holster and firearm.

Target Market: Concealed carriers, especially those people who do not care for the clipped design of most IWB holsters or those people who frequently have to remove their holstered firearm, for reasons such as entering areas where carry is prohibited. The clipless design of the holster makes it easy to remove the firearm and holster as one unit for safe storage in a legal location.

FNBs (Features & Benefits of this product):

  • Clipless Design allows for versatility in terms of holster location.
  • The holster allows for the user to choose pocket carry or IWB carry (Within certain limitations, mainly gun size.)
  • Easily cleaned if the holster becomes soiled.
  • Lightweight and not a lot of bulk.
  • Covered the hammer of my revolver completely rather than allowing it to stick out above the mouth of the holster. This can be an important consideration for comfortable carry.

What other aesthetic options or finishes are available?: The holster is offered in a simple, black finish that has a stitched outer border and a tacky rubber like substance that I can most closely approximate to the material that is put on the handles of exercise equipment.

What others are saying?: “This was purchased for my SP101, and is my third Sticky Holster. I prefer the versatility these holsters give over a standard IWB holster; much thinner than leather, no clips or straps to get in the way, and it stays put.” - Amazon Review

Price point:

I need it now! Availability (Where can I buy this TODAY?) Amazon.com or Sticky Holsters

Our Rating:

Pros:

  • Lightweight
  • Sticky material allows for placement in different places on the belt.
  • Clipless design removes the problem of belt loops getting in the way of the clip.
  • Versatility; the holster can be used as a pocket or IWB carry option.

Cons:

  • Holster can be somewhat bulky depending upon application. Pocket carry was pushing the limits of my pocket capacity (others may vary)
  • The material is quite thin. It seems plenty durable, but I would prefer a bit thicker, with perhaps a reinforced holster mouth (Says on the Sticky website this is coming soon)

Score: 7.5 Good

75

 

 

Ryan’s Links:

Handgun Radio

Alien Gear Cloak Tuck 2.0 IWB Holster Review

Alien Gear Cloak Tuck 2.0 IWB Holster The market for inside the waistband (IWB) holsters has seen a surge of innovation in design and materials in the recent years. At first glance they may all seem the same in form and function, but anyone who carries concealed on a regular basis will know the difference on the hip. Each concealed carrier has a different frame, and can be themselves a variable as to what brand of holster fits best. A lightweight holster with the right combination of materials can be the solution that fits wider (and thinner) range of people.

Enter the 'Cloak Tuck 2.0' from Alien Gear Holsters.  This IWB holster stands out from the pack with a unique composition. Technically referred to as a hybrid, the lightweight design has a soft Neoprene backing that is thinner and more flexible than traditional leather backings, and provides a better conforming fit and comfort to your body. The Neoprene material is completely waterproof, which will prevent corrosive sweat from soaking in and reaching your pistol. The secret to the backing is an internal ABS polymer core that gives flex but is strong enough to not sag down with the weight of a hefty handgun.

Alien Gear Cloak Tuck 2.0 IWB Holster

The Alien Gear Cloak Tuck 2.0 IWB Holster has a plastic handgun half-shell that is fully swappable for versatility with other guns in your collection. The shell is made in a quicker fashion than most other 'boutique' kydex holsters, and this simplicity in the manufacturing process trickles right down to the price tag for the end user. By no means is this a poor quality holster, just the responsibility for retention is shared amongst the belt, waistband of the belt, and the user's hip. I know it's far from rocket science, but sometimes the simpler solutions are the best.  The half shell reduced the overall profile of the holster, and thus prevents factors that cause imprinting of the firearm through clothing.

The Cloak Tuck 2.0 holster comes equipped either with Alien Gear's standard nylon clips, designed for 1 .25" to 1.5"  inch belts, or their steel clips that fit belts up to 1.75" inches. For enhanced conceal-ability, there are nylon "C" clips and "J" clips are also available on the website as add-on items. These clips would be ideal for anyone who tucks their shirt over the pistol, and does not wish to have obvious clips exposed over the top of the belt. The "C' or "J" clips go beneath the belt and hook under the edges, which gives a more innocuous look. The holster also includes a parts pack containing multi sized screws and rubber spacers, along with one T Nut, Finish Washer, and 3/32 Hex Key.

Alien Gear Cloak Tuck 2.0 IWB Holster

I ordered this holster for the Smith & Wesson M&P Shield, to really get a sense of concealability of a single stack defensive pistol. Borrowing a friend's Shield, we were both able to test the holster by drawing in the standing, sitting, and walking positions. After comparing notes, we both agreed the Cloak Tuck 2.0 had a better feel than other holsters we both respectively have tried in the past. The Neoprene was soft on the skin and keeps your skin from feeling sweaty, irritated or suffocated at the end of the day. The thinness and flexibility also made inserting and removing the holster from the pants easier than rigid leather-backed holsters. This, along with the lightweight, may also fit your regularly sized pants instead of having a designated pair thats one size up to accommodate an IWB holster.

The only factors I took as a trade-off with this holster are two-fold:  When reholstering the firearm, the flexible backing will deform instead of guide your muzzle downward into position. I found that reholstering from a slight angle caused this issue to repeat, and the slide could come out of battery. Leather offers more resistance that would guide the gun into position easier, but during an altercation the holstering is the slowest and least critical part anyways.  The second issue I found was more of a personal preference. Instead of grommeted or regular holes for adjusting the ride height, Alien Gear had installed all 6 nuts, leaving 4 exposed. While this makes for initial configuration faster and easier, removing the unused nuts with barbed backings would be more troublesome than leaving them installed, leaving them exposed WILL wear on your clothes overtime.

** I've decreased the rating to 6.5 since initially reviewing this holster, as issues and wear have shown more over time. Also, the positioning of the shell put the rear of the pistol's slide off center from the sweat guard. Modification to the screw holes was necessary to shift the gun over slightly so the slide and sights didn't jab my side when seated.**

Because the overall for the price point, this holster is hard to beat. Other brands on the market reaching as low as $60 or $50 dollars make compromises in either plastic vs kydex, or leather quality, or stitching reinforcement. For almost half that price, you can get a quality holster from Alien Gear that accomplishes exactly what and IWB holster should do, without abducting your paycheck!

Firearms Insider Reviews - 8 Key Points

Claim to Fame: Our 'Cloak Tuck 2.0' Neoprene Composite Holster is our most comfortable and stable holster yet. 

Target Market: Concealed Carry

FNBs (Features & Benefits of this product):

  • Lightweight design
  • Soft neoprene body-side layer
  • Inner ABS polymer core
  • Completely waterproof
  • Fully swappable handgun shell for versatility.
  • Comes equipped either with standard nylon clips, designed for 1 1/4 to 1 1/2 inch belts, or steel clips that fit belts up to 1 3/4 inches.
  • For enhanced conceal-ability, nylon "C" clips and "J" clips are also available as add-on items.

What other aesthetic options or finishes are available?: Black

What others are saying?: "Alien Gear has nailed it. The simple design means the cost comes in below most other holsters–$35.88.  New pieces and parts are available as needed. New Kydex shells, too. If you aren’t someone who owns a lot of guns, there’s always the shell-swap option.  All told, this holster is comfortable, dependable, easy to conceal, and modular. I’d pay a lot more than $36 for that."

Price point:

MSRP = $35.88

I need it now! Availability on aliengearholsters.com

Our Rating:

Pros:

  • The back layer of neoprene is very soft and didn't get excessively sweaty
  • Completely waterproof
  • Lightweight & comfortable for all day carrying
  • Slim profile reduces printing, can make IWB 1911 carry possible
  • Easy to get into pants
  • Includes varying sizes of nuts and spacers and the allen tool

Cons:

  • Neoprene backing is quite flexible, and reholstering at the wrong angle can hang up the process, cause slide to come out of battery
  • Logo artwork was wearing off (may have been temporary marking for short run of Clock 2.0)
  • Nuts are pre-placed and exposed, as opposed to one set of nuts to disassemble and adjust (removing nuts would cause damage to backing)
  • Position of the slide was off center from sweat guard and required modification of the shell
  • Others users have experienced rusting on the back's exposed screws, and even comfortable skin wear

Score: 6.5

 

 

Featured FFL:

For FFL services I choose Promised Land Firearms in Toulon, IL.

Ryan's Links:

Gun & Gear Review Podcast

Hunter of Design

Firing Line Review

Remora Clip-less Holster for Ruger LC9 Review

image (2)  

By: Larry

Upon first look of the Remora Clip-less holster, I thought there was absolutely no way this holster would work for me. However, after wearing this holster a number of times, I am amazed at the comfort. Often times I had to reach down to my hip to make sure my firearm was still intact. The non-slip material is everything as advertised. My firearm remained in place. Also, this holster is great as a deep pocket concealment holster. The price is very reasonable for just about everyone who wishes to conceal. Overall, I have very little complaint and I recommend this holster for anyone searching a low cost comfortable holster.

image (5)

Firearms Insider Reviews - 8 Key Pointsimage (10)

Claim to Fame: Conceals firearms with comfort

Target Market: Best servers conceal carrier with a low profile holster

FNBs (Features & Benefits of this product):

  • Light weight
  • Low profile
  • IWB or pocket carry
  • Ambidextrous
  • Closed design

What other aesthetic options or finishes are available?: Available in black only.

image (3)

What others are saying?: “This is a clip-less IWB from Remora. I wasn’t sure how well it would work, but the review I read on the LCP site was it very encouraging so I went for it. The holster is made from a slip resistant material and there is no need for a clip. I ordered the 2A with sweat guard for my LCP and a double magazine pouch also.” – eaglefrq, GlockTalk user

Price Point:

I need it now! Availability: I need it now! Availability Ships in 5-7 days directly from Remora and 1-2 days from Amazon.

Our Rating:

Pros:

  • Lightweight low profile design
  • Comfortable
  • Non-slip outer skin
  • Low cost

Cons:

  • Holster needs to be removed to re-holster after drawing
  • No belt clip

Score: 8.080

 

 

Featured FFL

Larry prefers Cops Inc. in Sycamore, IL for his FFL needs.

Alien Gear Holster Cloak Tuck Review

IMG_1528-1By James M. Smith IMG_1523In search for a high quality and good value holster I did a lot of looking and research before making a decision. When I came across Alien Gear Holster I was immediately intrigued. They offer, what appeared to be, a good quality holster at an exceptional price. They as offer their holster with a lifetime warranty. Of course, with a company that is only a couple years old that doesn't mean much, but hopefully they will stay around for a long time. I decided to go ahead and give Alien Gear a shot. For under $40 shipped I got the tan leather holster for my Full-Size M&P9. I was comparing this with the Crossbreed holsters and getting one of those with the horsehide and the “combat cut” would have been pushing $100. Is the Crossbreed worth the extra cost? I don’t know as I haven’t had any personal experience with them.

At the time that I ordered, shipping times were about three weeks and they were able to meet that deadline. The holster arrived in a nice padded shipping envelope and inside that was the start to a beautiful relationship. The holster was bagged in a cool black bag with Alien Gear's logo on it. This was a really nice touch for such a budget priced item.

The leather seems to be of high quality and had the edges are nicely smoothed. So, I unloaded my gun and inserted it into the holster and tightened the retention screws to make it snug. Now, as with most IWB holsters, you don’t get full retention until it is inside the waistband and your belt snugged up around it. Knowing this I made sure to make it snug but it was still loose enough that it will fall out if you do the standard retention test of turning the holster upside down. While doing these initial adjustments and inspections, I noticed one thing I do not like about the Alien Gear Holster. The leather and the kydex do not fully cover the trigger guard by the grip. Is this a huge issue? I don’t really think so. The trigger itself is fully covered and if anything were to get in there it would still be behind the trigger, so accidental discharges should not be an issue. It is just my pickiness that makes me even mention it. I feel that they can and should make a change to their molds and leather cutting process to get it fully covered. I don’t think it would affect the ability to get a good grip on your firearm for drawing. On that note I’m glad that I went with a combat cut holster. The combat cut has the leather cut really close to your firearms grip, so it is possible to get a firing grip while the gun is still holstered. This makes it so that you don’t need to do a lot of adjusting of your hand hold after it is out to the holster.

I don’t have much to compare with, but I find this holster to be very comfortable. It does not rub or pinch. I have not tested it in extreme heat yet, as I got it in March, but I have not experienced hot spots or anything. The only time I’ve really experienced any discomfort is when I am riding in my car. I have a hard time getting completely comfy in that car anyway. It is just a matter of finding the position.

Concealability. I think this is more of a factor of the firearm I carry. I carry a Full-Size M&P9 and with the large full-size grip it is hard to get good concealment. Even with the holster set at its lowest setting I have a hard time keeping the grip under my shirts.

IMG_1521

IMG_1522

 

 

 

 

 

 

Firearms Insider Reviews - 8 Key Points

Claim to Fame: Quality hybrid IWB holster at an affordable price.

Target Market: Anyone who wants to carry IWB.

FNBs (Features & Benefits of this product):

  • Iron Clad triple guarantee
  • 30-day money back test drive
  • Lifetime shell trades
  • Forever Guarantee
  • Adjustable cant and ride height
  • Adjustable retention
  • Thick sweat proof leather
  • Tuckable
  • Combat Cut

What other aesthetic options or finishes are available? Natural or Black dyed leather. There are many different gun shells available. Now available in an OWB configuration and combo kit (IWB and OWB). They also have leather belt loops available instead of the steel spring clips. All of these options are available from Alien Gear Holster's website.

What others are saying?:Concealed Nation "Best Holster Ever“ 

Price point: 

I need it now! Availability: The Alien Gear Holsters Cloak Tuck can be purchased directly from Alien Gear Holsters. Facebook

Our Rating

Pros:

  • Low Cost
  • Comfortable
  • Great warranty, test drive, and shell exchanges
  • Tons of shell selections

Cons:

  • Doesn’t fully cover the trigger guard on my FS M&P
  • Not a huge selection of holsters for guns with lights or lasers

 Score: 8.080

Comfort Holsters Bentley Comfort Holster Review

Bentley Comfort Holster I really love it when my initial impressions of a product are wrong. When I first received the Bentley Comfort Holster, I thought the unique materials were some sort of gimmick to justify the premium price tag. After carrying with the holster for a few days in a row, I'm happy to say "Boy, I was wrong!" There's an metaphoric expression used to compare the quality of a product to a highly reputable classic car maker... "the Rolls Royce of ___" is what people say. I can venture to say that this holster got its name, because it is "the Bentley of Holsters."

First let me preface by stating that I own several different inside the waistband holsters, and they each have gotten their fair use.  I do have a favorite out of the bunch, that has warped to my body after being worn repeatedly, and feels pretty good now that it's been 'Ryanitized' by my love handles. By the end of the evening, especially if it was a particularly active day, my body is relieved when its time to take that holster off. The air finally gets a chance to wick away sweat that accumulates with unbreathable skin-on-leather contact, even with a layer of fabric in between. Then there's the circular indent left behind. I do not expect the comforting concept of having a concealed defensive pistol to be in itself comfortable to bare, and that has been a mantra in the concealed training world for awhile now. With all the advancements in leather and kydex, we still have to endure some discomfort in order to be secure when using conventional IWB holsters. I'm pleased to have found an alternative that effectively throws that paradigm out the window.

Bentley Comfort Holster

Comfort Holsters claims this is the most comfortable holster in the world. A bold claim indeed, something that every holster manufacturer attempts to boast! The flagship model in Comfort Holsters' product line is called "The Bentley Comfort" holster. The Bentley uses a unique gel layer wrapped in suede material, which pads a full kydex chassis on the hip-facing side. The full chassis of kydex provides maximum retention of the firearm, while protecting the metal's finish from sweat. The gel pad reminds me of high end orthotic insoles in a prescription shoe, which is actually a really good way to compare the beneficial qualities of the material. Gel obviously molds to outside forces, your hip in this case. This eliminates abrasions, chaffing, and putting undue pressure on your body that some conventional IWB holsters can cause. Now wrapping that jelly material in soft suede not only feels pleasant to the touch but allows skin the breathe, which resolves something a leather backed holster design suffers from greatly. The result is an all day comfort that I personally had never really appreciated until it came time to remove the Bentley from my pants at the end of  day one... the relief of pressure and drastic "Aaaaahhh, much better" feeling was missing. Meaning the Bentley and my body were ready for another 9+ hour day of carrying, and that's a feeling I have never experienced with any other holster I've tried.

Bentley Comfort Holster

The Bentley holster has two leather tabs, more like wings, that provide the mounting for two belt clips. Unlike other holsters, the clips are not spread out. The Bentley is smaller more compact design with clips specifically placed asymmetrically for functional purposes. The rear clip is less than an inch from the kydex, with its clip positioned underneath the pistol grip. This, combined with a short, rigid double layer of leather which the manufacturer calls the "Cling Tab," causes a pulling / torque of the holster inward so that the grip follows the contour of your body, instead of remaining parallel to your frame like other holsters. The front/foward tab is a single layer of leather and is longer and mounted to follow the inward taper of the kydex, allowing it to flex and follow the contour of your waistband. This design has two primary intended results: reduce "printing" or broadcasting you are concealing a firearm through an imprint in clothing, and not needing a break-in period for the holster to warp and conform to your body.

Bentley Comfort Holster

From my testing, which included drawing my S&W M&Pc for dry fire practice for a couple weeks, I found that I am pleasantly pleased with the Comfort Holsters Bentley Comfort holster. The marketing hype on the Comfort Holsters website seems overreaching if you've never given it a try, but I can honestly assess that a lot of thought and engineering went into designing and building a better IWB holster. Some personal notes I found during my testing and evaluation are:

  • If you prefer to carry exactly in the 3 o'clock position, the Bentley doesn't feel 'right'. It printed much more for me at this apex of my hip. I found that moving it back to the 4 - 4:30 position was the 'sweet spot' for me. I normally don't carry this far back because more traditional IWB holsters have a wider leather backing, and would cause pinching/discomfort in the kidney area when in the sitting position. The Bentley's smaller profile was almost unnoticeable when sitting at my office desk and driving around town.
  • The rearward clip on the Cling Tab is directly located below the front strap of the grip, and if you adjust the seating depth so your gun sits deeper in your pants, the clearance for your fingers gets really tight. My digits began to wear on the knuckles of the index and middle fingers during drawing practice, and would often interfere with getting a good purchase on the grip frame. I wouldn't say that I have gorilla mits, but if you have fatter booger hooks than I do you will encounter this too. Best to leave the rear clip in its lowest position.
  • The smell of the adhesive that binds the suede/gel panel to the kydex body is very pungent. If it weren't for the instructions addressing this, I would have been concerned for my safety in a tightly spaced environment. No worries, the off gassing dissipated after about 2 days.

Note: If you want a holster made to fit your rail mounted light or laser, just ask Rob. I wish I had a TLR-3 on a S&W M&Pc molded up, but failed to ask.

Firearms Insider Reviews - 8 Key Points

Claim to Fame: This is the most comfortable holster known to man

Target Market: Concealed Carriers looking for the ultimate comfortable hoster for IWB carry

FNBs (Features & Benefits of this product)

  • Gel Cushion
  • Suede Protection
  • Tuckable
  • Adjustment clip position (3 levels for forward clip, 2 for the rear)
  • Rigid & short Cling tab gives extra support to rear of holster, angles grip inward
  • Full Kydex body retention
  • Small Footprint
  • Lifetime Guarantee
  • 6 week buy back warranty
  • Made in the USA
What other aesthetic options or finishes are available?:  Kydex color Black or Desert Tan

What others are saying?: " During a very extensive search for an IWB holster to fit my glock 19 AND mounted Streamlight TLR-1, I ran across Rob Durham. When I first contact Rob he was in the process of moving his shop into the back of one of his local gun shops. This move has enabled him to make holsters for pretty much anything that the shop might carry. After hammering out all the details of what I was looking for Rob was able to put together a mold for my combination and for future use... Instead of leaving a waxed backing on the holster Rob has mated a second layer of leather for added comfort. It does not affect the flexibility of the holster. It doesn't affect the thickness either. This holster is fairly thin. I think I would have liked to see him run a row of stitching In the sculpted track running the entire perimeter of the holster, but we'll see how it holds up in the long run as is. The Holster is set up for adjustable ride height and/or cant... The holster features a sweat guard. As of right now there is not a "combat cut" like cross breed offers. But I have a feeling it will be an added feature in future holsters. It does not effect the draw, but would be a tad more comfortable on first "grab". After playing with the cants I finally settled in on the front clip all the way to the top and the rear clip in the middle position. At the 3 o'clock position it provides a slight cant, and makes the weapon print ALOT less.... is directly on the hip. You'll notice in this position that it "squares off the side." Also noted a bulge around the pocket. This position is NOT okay while seated. The grip and sweat guard tends to push into my side in this position while seated." Firing Line User Review

Price Point:

I need it now! Availability: Readily available at comfortholsters.com

Our Rating: +  No break-in period +-Cling Tab: Shorter, double layered tab pulls pistol grip in to follow body contour + Suede and Gel combo really does provide all day comfort, no sweating or chaffing especially if in sitting positions (at desk or driving) + 6 Week Buy Back guarantee, shows major faith in product / customer satisfaction -  Smaller footprint puts rear clip right under pistol grip and can hinder initial purchase of handle if preferred position adjusted a certain way - My experience with experimenting with different pants / tops was still signs of printing through light clothing due to full kydex body and gel pad. --Strong glue smell upon first 1-2 days of wear - Price is on the higher end of the market, but it is high quality with uniquely comfort not available elsewhere.

Score: 8.0 Great

 

 

Glocktech MIC Holster Review

20140727_174018 The Glocktech MIC holster is a zero bulk holster for deep concealment. The idea came about from a law enforcement officer in the mid 90s. Detectives and undercover officers were carrying their firearms by just sticking them in their waistband, sans holster. Mitch, the creator, says  there was a need for a safer alternative, without having to add the bulk of a full belt holster, and thus, the Minimal Inside Carry(MIC) holster was born. It is small, molded Kydex piece that is formed around the trigger guard and is available for 32 different firearms. It simply slips over the trigger guard and protects the trigger. On the front of the holster, just forward of the trigger guard, there is a hole with a cord through it. The cord wraps around your belt, then you stick the holstered pistol into your waistband. The cord that is wrapped around your belt does two things. The first concern of non-holstered carry is that your pistol could slip down your pants and out of your leg, possibly being kicked across the floor at the most inopportune moment. The cord keeps it from going too far down, and falling out. Its other purpose is to adjust carry depth. You can shorten or lengthen the cord by putting a knot in it. If you want it deeper, make the knot further from the holster and if you want it higher, put the knot closer to the holster.

Drawing from the MIC is a little different from a normal holster. You have to draw it with far enough to get the holster to detach from the pistol. It does take a little force, also, so you would need to pull the holster out more vigorously than you would a Kydex, leather, or hybrid holster. You can also draw it to where it is just out of your waist band, then push forward. This will free the holster from the pistol. Watch the video below for visuals of the drawing techniques.

Where this holster shines, is that you can quickly adjust its cant and position without removing a holster. If you carry on your strong hip, driving with a traditional holster can be uncomfortable, because the butt of the grip pushes against the seat and squishes the pistol into your side. With the MIC, there is enough flexibility, with the lack of clips, that it just simply gets pushed forward and makes driving armed incredibly comfortable. The downside to this is that when you exit your vehicle, you’ll have to adjust it back to your normal cant. If getting in and out of a vehicle all day, it may get a little annoying, but if you’re driving all day, it really makes it comfortable.

20140727_173409

Another feature of the MIC is that the cord is heavy enough and the retention is tight enough that if your pistol is somehow knocked/worked loose from your waistband, it holds the pistol, instead of it just hitting the floor. It would be an awkward, and possibly illegal, situation, but at least your gun wouldn't be lying on the floor of the grocery store check-out line for someone else to pick up.

One last feature is that you can wrap the cord around the base of your seat in a vehicle and use the holster in the vehicle by jamming it in between your seat and console. The holster covers the trigger guard and also keeps the pistol from bouncing around in the event of a collision or a sudden stop. See Mr Colion Noir’s video for a better description.

20140727_174345

Glocktech also offers an upgrade for the cord. They call it the Versa Cord. It is a heavier cord than the included one, and it is about twice the length. They advertise it for giving even more range of adjustment, and to also keep something covering your trigger when pocket carrying.

I personally think the MIC is a great holster, but I may be a bit hesitant to refer it to a new concealed carrier. The reason why, is that the handling pretty unorthodox.

Firearms Insider Reviews - 8 Key Points

Claim to Fame: Zero bulk, concealed carry holster

Target Market: Concealed carriers and discreet law enforcement officers

FNBs (Features & Benefits of this product):

  • Zero bulk
  • Adjustable carry depth
  • Very versatile
  • Great for driving

What other aesthetic options or finishes are available?: The MIC is only available in black, but, despite the Glocktech name, the MIC is available for many more firearms.

What others are saying?: “When you use a product like this, you have removed all the risk of this type of carry” –The Yankee Marshall

Price Point:

  • MSRP = $18.95 + Shipping
  • MSRP = $20.95 for MIC with Versa Cord
  • Retail = $22.99 with Free shipping

I need it now! Availability: You can purchase the Glocktech MIC holster from Amazon and directly from Glocktech.

Our Rating:

+-No bulk +-Simple +-Versatile +-Great for driving +-Inexpensive

--A little bit of a nuisance when going from sitting to standing

Score: 9.0 90

N82 Tactical Original Holster Review

IMG_0949.jpg

N8 Squared Original with Glock 19 Although my current geographical situation precludes me from carrying concealed, being a good American consumer, and a lover of all things gun related, I still get holsters every once in a while. Perhaps, it's just in case hell freezes over and NJ becomes a shall issue state, or maybe as a pinch of preparedness. Either way, just like my firearms collection, the handguns that I have holsters for are varied. Outside the waistband holster for the like of my Sig 226 and kydex IWB holster for my Glock 19 and now the N82 Tactical Original for my little J-frame or Glock 19.

N82 Original with SW Airweight

In carry philosophy, there are a few ideals which need to be lived up to in varying degrees. One is the concept of that the best carry handgun is the one you have with you, it is the one that you will have on your person every day no days off. This can be lived up to, depending on where you are located, where you travel, work, etc. Another one is more in the application of the holster. The weapons security is crucial in a defensive scenario. You could need to run, drive, or carry someone, basically anything that would require two hands in the middle of, or after, the shooting. For the very same reason you use a holster in the first place and carry it concealed, you want to carry that defensive tool in as safe and secure a manner as possible. What I am getting at is re-holstering ability. If you pocket carry with no holster, then it’s a moot point, but if you're carrying using a holster, the ability to re-holster that defensive tool could be a deal breaker in your philosophy of use.

To me, these are the two biggest considerations, aside from concealability, to consider when choosing a holster. A concealed carry permit does you no good if you can’t carry safely in all manner of dress or it is not comfortable and you leave it at home. So, to me, the consistency of your carry slightly edges out re-holster ability.

Something else that impresses me is the price. The most powerful impact of the concealed carry movement is that it re-took the right to self defense from the elite and rich and brought it back to the people. The affordable price point on the original design makes a very comfortable, secure carry system available to more people which, in my book, is a good thing. Put a used J-frame in this holster and for less than 300 bucks total you will have a reliable proven gun with great defensive loads in a comfortable, secure holster and, all-in-all, will be a system that can pretty much disappear on most people.

Firearms Insider Reviews - 8 Key Points

Claim to Fame: Concealment, Comfort.

Target Market: Entry level carry

FNBs (Features & Benefits of this product):

  • Suede leather backing
  • Neoprene midlayer
  • Steel Clip
  • Comfortable against the skin
  • Neoprene stops body oils and sweat from contacting firearm
  • Thin and minimalist design improves concealability

What other aesthetic options or finishes are available?: They make this same holster but with a different clip that makes the unit tuckable. They also make the professional line which is a polymer molded unit attached to the same comfortable platform. N82 products page

What others are saying?:

Big Tex Outdoors Youtube

Price point:

MSRP = $39 +9.50 shipping Retail = $39 +8 shipping at Tacdaddy.com

I need it now! Availability: You can buy these at the above mentioned sites and a quick Amazon search yielded two left handed models on there but no right handed models.

Our Rating

+-Comfort +-Concealability +-Construction

--No re-holster ability

Score 7.575

 

Featured FFL:

I enjoy working with Dynamic Combat Solutions in Wayne, NJ for all my FFL services and custom gunsmithing needs.

My Links

NJ Gun Blog

Guns Of Hollywood Podcast

Alien Gear IWB Holster Review

58201418928 Written by Chad Wallace

582014181059I ordered the Alien Gear IWB holster because I liked the price.  The holster is everything I expected it to be and more.  The Alien Gear holster is an Inside The Waistband (IWB) holster of the hybrid variety.  It has a large leather back panel and a kydex shell.  This holster is tuckable and comes with metal belt hooks, an option is available for leather hoops also.  The holster arrives with a bag full of extra hardware, which can be used to vary the amount of tension on the gun.  It varies the tension by adjusting the screws that hold the shell on.  Between the shell and the leather backing are some rubber grommets to do this tension adjustment.  Ride height and cant can also be adjusted by moving the belt loops around.  I ordered the tan leather but black is also available as an option.  The holster is available for a vast selection of pistols and comes in a combat cut only, this means that the grip of the pistol is not backed by leather and therefore it rests against you skin or undershirt.   An option is also available to just purchase the outer shell, or trade your original shell, for a new one if you change firearms.  I experienced the shell swapping, because on my original order they sent my holster system for the wrong firearm.  I contacted them and they sent a new shell out the next day.  This was great, until the new shell came for the same wrong firearm.  It then took 3 weeks to finally get a hold of them to tell them about the new mix up. So 5 weeks after the initial holster arrived I received the correct shell and was able to try the holster out.  I have found the holster to be really comfortable and hides the firearm nicely.  

58201418725

Firearms Insider Reviews - 8 Key Points

Claim to Fame: Inexpensive quality IWB holster with the option for gun interchangeability.

Target Market: Those wanting a hybrid IWB holster for a decent price.

FNBs  (Features & Benefits of this product):

  • Hybrid Design
  • Price
  • Changeable Shells and/or free shell trades
  • Forever Warranty
  • Adjustable angle
  • Adjustable ride height
  • Adjustable tension
  • Tuckable
  • Extra hardware

What other aesthetic options or finishes are available?:

  • Comes in tan or black leather
  • Available for a vast selection of pistols

What others are saying?:  From the AlienGear website:58201418825

  • Great product, great value!
  • Very nice product, my only negative thing its the time that I have to wait since order date until it's ready to ship
  • Great Value

Elsewhere on the web:

  • Just got my Alien Gear holster in today and it is a great holster
  • A decent piece for the price, but it is not a replacement for a higher end hybrid
  • Very nice! Super comfortable!

Link to other reviews:  TexasCHLforum,  YouTube

Price Point:

I need it now! Availability:  Aliengearholster.com but shipping times are about 4wks

Our Rating:

  • Price
  • Comfort
  • Adjustments
  • Extra hardware

  • Customer Service

  • Shipping times (about 4 weeks from order date)

Score: 7.0 Good 70

Chad’s Favorite Link: Northwest Firearms